606707
22
Zoom out
Zoom in
Previous page
1/77
Next page
SIGNALING-2
CTCSS FREQUENCY SCAN
This function scans through all CTCSS frequencies to identify
the incoming CTCSS frequency on a received signal. You may
nd this useful when you cannot recall the CTCSS frequency that
the other persons in your group are using.
1 Press [TONE] 2 times to activate the CTCSS function.
• The icon appears on the display when the CTCSS function is
ON.
•• Each press of [TONE] changes the selection as follows:
Tone (
) CTCSS ( ) DCS ( ) Cross Tone ( :
default) Off (no display).
2 Press [F], [T.SEL] (1s).
• The icon blinks and “SCAN” appears on the display.
Scan starts when a signal is received.
To reverse the scan direction, turn the Tuning control clockwise
(upward scan) or counterclockwise (downward scan). You can
also press microphone [UP]/ [DWN].
To quit the scan, press [ESC].
When a CTCSS frequency is identifi ed, the identifi ed frequency
appears on the display and blinks.
3 Press the Tuning control to program the identifi ed frequency
in place of the currently set CTCSS frequency.
The CTCSS function will remain ON. To cancel CTCSS, press
[TONE] until CT no longer appears on the display.
• Press [ESC] if you do not want to program the identifi ed
frequency.
• Rotate the Tuning control while an identifi ed frequency is
blinking, to resume scanning.
USING DCS
1 Select your desired band.
2 Press [TONE] 3 times to activate the DCS function.
• The icon appears on the display when the DCS function is
ON.
Each press of [TONE] changes the selection as follows:
Tone (
) CTCSS ( ) DCS ( ) Cross Tone ( :
default) Off (no display).
3 Press [F], [T.SEL].
The current DCS code appears on the display and blinks.
4 Rotate the Tuning control to select your desired DCS code.
Refer to the table below for the available codes.
To exit the DCS code selection, press [ESC].
5 Press any key other than the Tuning control and [ESC] to
complete the setting.
6 When you are called: The transceiver squelch opens only
when the selected DCS code is received.
When you make a call: Press and hold [PTT], then speak
into the microphone.
To cancel DCS, press [TONE] until DCS no longer appears on
the display.
You can also select a DCS code by using the microphone:
1 Select your desired band.
2 Press [TONE] 3 times to activate the DCS function.
• The icon appears on the display when the DCS function is
ON.
Each press of [TONE] changes the selection as follows:
Tone (
) CTCSS ( ) DCS ( ) Cross Tone ( :
default) Off (no display).
3 Press [F], [T.SEL].
The current DCS code appears on the display and blinks.
4 Press the key programmed as [ENTER].
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info