606707
20
Zoom out
Zoom in
Previous page
1/77
Next page
SCAN-4
VISUAL SCAN
While you are receiving, Visual Scan allows you to monitor
frequencies near the current operating frequency. Visual Scan
graphically and simultaneously shows how all frequencies in the
selected range are busy. You will see up to 21 segments, for each
channel, that represent 7 S-meter levels (3 segments per level).
Determine the scan range by selecting the center frequency and
the number of channels. The default number of channels is 61.
Cursor
S-meter level
Selecting the Number of Channels
1 Enter Menu mode and access Menu 916.
2 Set the number of channels to MODE 1 (31ch), MODE 2
(61ch), MODE 3 (91ch), or MODE 4 (181ch).
Using Visual Scan
1 Select your desired band.
2 Rotate the Tuning control select the operating frequency.
This frequency will be used as the center frequency.
3 Press [F], [VISUAL] to start Visual Scan.
To halt Scan, press [PAUSE]. “PAUSE” appears and blinks.
Press [PAUSE] again to resume.
4 To change the operating frequency, rotate the Tuning
control.
The displayed frequency changes and the cursor moves.
• Press [SET] to use the changed operating frequency as the
center frequency.
• Press [RESET] to restore the previous operating frequency.
5 To exit Visual Scan, press [ESC].
Note:
You cannot use the Visual Scan Function under the following
circumstances:
When the APRS/NAVITRA or Packet mode is turned
ON.
When only 1 channel has been stored in the memory
channels.
When using Weather Alert (K models only).
If you start Visual Scan in Memory Recall mode, the memory channel
frequencies will be scanned.
If you start Visual Scan after recalling the Call channel, the Call
channel frequency will be used as the center frequency.
If the frequency range specifi ed for Program Scan or Program VFO
is narrower than the range specifi ed for Visual Scan, the range for
Program Scan or VFO will be used for Visual Scan.
Visual Scan stops while transmitting.
If you start Visual Scan in one of the following conditions, you cannot
receive in the current operating frequency. To use this frequency, press
[PAUSE] to halt Scan.
Memory Recall or Call Channel mode.
A frequency in the 118, 220, 300, or 1200 MHz band was selected
in VFO mode.
Depending on the transceiver conditions, Visual Scan and the
conventional S-meter may indicate different signal strength levels.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info