686371

Kemppi Robot Gun Mount T1 Manual

14
Zoom out
Zoom in
Previous page
1/22
Next page
14
Robot Gun Mount T1© Kemppi Oy 2017 1712
OPERATING MANUAL
5. Screw the pull-in tool (1) into the cable assembly connection (4) as far as it will go.
6. Pull the cable assembly through the 5th and 6th axes of the robot into the robot
mount as far as it will go, using the pull-in tool.
Position the cable assembly connection (4) by means of the positioning pin and the
groove of the welding torch coupling (11).
7. Secure the fastening screw (14), with max. tightening torque M = 7.5 Nm. Observe
the forced positioning.
Only if the cable assembly connection (4) has been correctly inserted can it be
attached with the fastening screw (14).
8. Unscrew the pull-in tool (1).
9. Slide the corrugated hose at the cable assembly (6) into the corrugated hose clamp
(9) as far as it will go, and clamp with cylinder screws.
Press the corrugated hose into the corrugated hose clamp, and rotate it until it is
rotating in the corrugated hose clamp.
10. Screw in the threaded sleeve (2) as far as it will go, and allow the bellows (3) to lock
into place in the groove.
11. The position numbers in the directions below refer to the following gure, showing
axis positions.
12. Attach the wire feeder (1) to the wire feeder mount (3).
13. Fasten the cable assembly (2) to the wire feeder (1) by using the connection
provided for connection to the machine.
14. Mount the control line of the robot mount for the EMERGENCY STOP switch at the
wire feed unit.
15. Unscrew the fastening screws at the wire feeder (1).
We recommend the following procedure for determining the optimal position of the
wire feeder at extreme welding positions:
Figure 9: Movement allowance
1 32
1. A4 = torsion max. ± 155°
2. A5 = torsion max. +90° / -165°
3. A6 = torsion max. ± 200°
Torsion A4 plus A6 is max. ± 355°.
See also Section 11.1.
Please observe the operation instructions for the relevant wire feeder.
• The wire feeder can be adjusted horizontally by means of long holes; do not
tighten them during the installation of the cable assembly. Swivel the robot
on the 5th axis by +/- 90°. After that, carry out a torsional movement on the
6th axis by +/- 240°. This will precisely position the wire feeder.
16. Tighten fastening screws at the wire feeder (1).
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Robot Gun Mount T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Robot Gun Mount T1 in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info