686383

Kemppi Kemparc SYN 500 Manual

12
Zoom out
Zoom in
Previous page
1/26
Next page
EN
You can change the gun selection by pressing buttons P3 and P4 again, as above. With a
liquid-cooled gun selected, the liquid cooling function is started when the power source is
started the next time.
2.2.6 Retrieving weld data
The weld data function allows you to return to the welding current and voltage used during
the previous session, with the weld data feature. To use the feature, press buttons P4 and P5
simultaneously.
2.2.7 Selecting the welding process
The welding process selector button P9 allows you to select the welding process you want to
use. You can select one of the following processes:
• normal MIG welding
• 1-MIG welding
• WiseThin (optional)
In normal MIG welding, the wire feed speed and welding voltage are adjusted separately.
Unlike the above, the 1-MIG and WiseThin processes are synergetic welding processes where
the welding voltage and other welding parameters are interconnected so that the welding
power and arc length are adjusted to attain optimal welding values.
The WiseThin process is an optional feature intended for welding automation. It must be
acquired separately and is therefore not available in all congurations.
2.2.8 Additional MIG features included in the standard delivery
The standard welding machine delivery includes three additional MIG features that facilitate
welding and improve weld quality. These additional features are creep start, hot start and
crater ll.
To use an additional MIG feature, press the feature selector button P10. Press the selector
button repeatedly to use one or several features. Only the additional features allowed for the
welding method you have chosen will be available.
Creep start
The purpose of the creep start feature is to make controlled weld start easier and smoothen
the initial stage of welding, for example when welding with high wire feed speeds. At the
beginning, the machine will use a slow wire feed speed until the wire touches the work piece
and the current starts owing.
Creep start is available for normal MIG welding and the synergetic 1-MIG welding.
Hot start
The purpose of hot start is to reduce start faults, for example when welding aluminium or
other materials with particularly good thermal conductivity. In this scenario, there is a xed
pre-gas time at the beginning of the welding, after which the welding power briey rises
above the specied power level. The power and time parameters for hot start can be specied
in the SETUP settings.
Hot start is available for synergetic 1-MIG welding.
Crater ll
The purpose of crater ll is to facilitate controlled nishing of welding and to reduce the
welding faults caused by the nal crater. When you press the welding gun trigger completely
down at the end of welding, the welding power is reduced to a preset crater ll level. To end
the crater ll stage, release the gun trigger. The crater ll parameters can be specied in the
SETUP settings.
Crater ll is available for synergetic 1-MIG welding.
10
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Kemparc SYN 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Kemparc SYN 500 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info