Manual Kemppi A7 TIG Orbital System 300 (page 27 of 61) (English)

686409

Zoom out

Zoom in

1/61

A7 TIG Orbital System 300© Kemppi Oy 2016 1615

OPERATING MANUAL

3.3.3 Options Menu

Any changes made on this screen become active

immediately but are lost when the power is switched o. To

maintain changes, press Save after all changes are made on

the screen.

Setting the weld counter

At completion of each weld, the system stores the actual

parameters run and related weld ID number, operator

name, and time and date to print out if necessary. The

weld number sequentially increases by one digit per weld.

You can set/reset the weld counter at any specic number

using the control knob.

Setting the password

Press Enter. Password screen appears. Press Enter. An

alphanumeric pop‐up eld appears. Enter a password up

to 10 characters using the technique described in section

Alphanumeric labeling. To conrm password, press Save.

Entering operator’s name

Enter operator’s name using the technique described in

section Alphanumeric labeling.

Setting date and time

Press Enter to select the Date/Time eld and set date and

time.

Setting the language

Use the control knob to scroll through the alternatives.

Setting the units of measure

The control knob lets you scroll between Standard and

Metric.

Using the test mode

If you need to use the test mode, use the control knob to

select Yes.

This mode allows simulation of an actual weld with

sequencing through the weld program and simultaneous

rotation of the weld head. By using this function You can

observe the rotation of the tungsten electrode while

changing the various levels of the program on the display.

It is a useful diagnostic tool if you suspect malfunction

during the weld mode. A service technician can operate

the system in a simulated weld mode without the need to

worry about the arc. In the test mode, the contactor signal

to the power supply is disabled, preventing initiation of

high frequency and a welding arc.

1. Exit the Options menu.

2. Select a program to run. TEST MODE appears on

the screen.

3. Press Start Weld.

Following the pre‐purge and current upslope time

interval, the rotation motor on the weld head becomes

operational. It will continue operation until current

downslope is over. If the Auto Rewind function has been

programmed to occur, it follows after the completion of

the simulated weld. The gas solenoid is pulled in during

pre‐purge, welding, and post‐purge.

For weld head models equipped with a ller wire

feeder, the ller wire feed motor is disabled during the test

mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 TIG Orbital System 300 in the language / languages: English as an attachment in your email.

The manual is 4,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kemppi A7 TIG Orbital System 300 Manual

Product: