686408

Kemppi A7 TIG Orbital System 150 Manual

9
Zoom out
Zoom in
Previous page
1/48
Next page
9
A7 TIG Orbital System 150© Kemppi Oy 2016 1615
OPERATING MANUAL
1.4 Controller unit
A7 TIG Orbital System 150 power source and cooling unit
are integrated inside the controller unit. This unit also
involves a printer to print welding parameters on paper.
The parameters can be saved on a memory stick through
the USB port. Programs can be stored in internal memory
(100) and saved on a memory stick.
1.4.1 Front panel
A7 TIG Orbital System 150 features a clear color display, a
control knob, and press buttons. Its intuitive graphical user
interface oers easy-to-use menus and auto programming
for automatic calculation of welding parameters, including:
• Electrode length calculator
• Creation of custom programs
• Instructions and information for the operator.
The power source front panel provides the controls to
develop, save, and call up welding programs.
1.4.2 Gas flow
The power source is equipped with a gas ow sensor that
is factory preset. Shielding gas must be owing to the
weld head to initiate a welding arc.
• If gas ow is insucient, pressing the Start Weld
button will not initiate a welding arc.
• If the gas ow is interrupted during welding, the
sensor will immediately extinguish the arc. A
warning message is displayed.
1.4.3 Water cooler
The controller unit contains an integrated water cooler
that monitors water circulation, and any failure or block
causes an alarm.
The water ow function is factory calibrated. Interruption
or insucient water ow (less than 0.5 LPM) results in
termination of welding and a warning message on the
display.
Water ow
The water ow sensor has a factory preset trip point that
is not adjustable.
• If water ow is insucient to actuate the
sensor, a welding arc cannot be initiated.
• Pressing Start Weld causes pre‐purge. When the
arc should be initiated, the starting sequence is
interrupted and a warning is displayed.
1.5 Compatibility
A7 TIG Orbital System 150 controller is compatible with
the 150 series of weld heads.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 TIG Orbital System 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 TIG Orbital System 150 in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info