686369
41
Zoom out
Zoom in
Previous page
1/66
Next page
41
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
6.1.12 StartWelding
This signal function controls the welding sequence. If
SimulationMode is set to be on, it controls a simulation
sequence instead.
This signal has an eect only if welding is allowed
(WeldingAllowed is set to 1).
0 = Welding / simulation o
1 = Welding / simulation on
6.1.13 WireInch
This signal function feeds the welding wire forwards. The
wire is fed at the speed of 1.0 m/min for 3 seconds and
then stepped to 5.0 m/min.
0 = Wire inch o
1 = Wire inch on
This signal has no eect during welding or simulated
welding.
6.1.14 WireRetract
This signal function feeds the welding wire backwards.
The wire is fed at the speed of 1.0 m/min for 3 seconds
and then stepped to 5.0 m/min.
0 = Wire retract o
1 = Wire retract on
This signal has no eect during welding or simulated
welding.
6.1.15 GasBlow
This signal function opens the shielding gas valve. The gas
valve can be controlled during welding, but not during
simulated welding.
0 = Gas valve closed
1 = Gas valve open
6.1.16 AirBlow
This signal function opens the compressed-air valve.
0 = Air valve closed
1 = Air valve open
This signal has no eect during welding or simulated
welding.
6.1.17 TouchSensorToolSel
This signal function sets the selection of the touch sensing
tool between the welding wire and the gas nozzle, if the
tool is not forced to selection either from the web user
interface or from the setup panel.
0 = Welding wire as touch sensing tool
1 = Gas nozzle as touch sensing tool
6.1.18 TouchSensorOn
This signal function sets the touch sensor power source
and the touch detection device to be on. The touch voltage
depends on the user settings. For more information, see
A7 MIG Welder operating manual.
0 = Touch sensor o
1 = Touch sensor on
This signal has no eect during welding or simulated
welding.
6.1.19 OnlineControl
This signal function enables robot-controlled values
for welding wire feed speed, voltage, ne tuning, and
dynamics. When the robot is in online mode and uses
the WireFeedSpeed, Voltage, FineTuning, and Dynamics
control functions, the corresponding values in the active
memory channel are overridden. When the robot is in
oine mode, it gives full control to the welding system
and the values from the active memory channel are used.
0 = Robot in oine mode. The wire feed speed,
voltage, ne tuning, and dynamics values are
obtained from the active memory channel.
1 = Robot in online mode and controlling
the wire feed speed, voltage, ne tuning, and
dynamics.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Welder 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Welder 350 in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info