686369

Kemppi A7 MIG Welder 350 Manual

42
Zoom out
Zoom in
Previous page
1/66
Next page
42
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
6.1.20 Watchdog
This signal function resets a watchdog timer in the robot
interface unit on each transition. The signal takes an
eect when the watchdog function is turned on from
the web user interface or from the setup panel. If the
watchdog functionality is on and the robot can’t maintain
transitioning of this signal, the welding system goes into
an error state. This prevents welding accidents if the robot
loses control over the welding system.
6.1.21 ErrorReset
This signal function resets the ErrorNumber value and the
Error signal to zero on the rising edge of the signal when
there are no active errors in the system. If there are any
active errors, the signal has no eect. The error is active
when the error situation is not resolved.
• 0 = Normal operation
• 1 = Error reset (on rising edge)
6.1.22 HotStartOn
This signal function controls a hot-start on and o, if the
hot-start is enabled to be controlled by a robot from the
web user interface or from the setup panel.
• 0 = Hot start o
• 1 = Hot start on
6.1.23 CraterFillOn
This signal function controls a crater-ll on and o, if the
crater-ll is enabled to be controlled by a robot from the
web user interface or from the setup panel.
• 0 = Crater ll o
• 1 = Crater ll on
6.1.24 DigitalOutput1 – DigitalOutput8
These eight signal functions set digital outputs in an
external I/O device to be active or inactive.
• 0 = Output inactive
• 1 = Output active
6.1.25 WireFeederSelect
This signal function is used to select the wire feeder in a
system that supports two robot wire feeders. The support
of two wire feeders is enabled by installing an extension
kit into the robot interface unit. See the A7 MIG Welder
Operating manual for details.
To be able to select the wire feeder by the means of this
signal, the function must be enabled from the welding
system settings by setting the Wire feeder option to
SELECT AT ROBOT.
• 0 = Wire feeder 1 (the primary wire feeder) is
active.
• 1 = Wire feeder 2 (the secondary wire feeder) is
active.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 MIG Welder 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 MIG Welder 350 in the language / languages: English as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info