598220
22
Zoom out
Zoom in
Previous page
1/476
Next page
Getting Started
2-8 2001-900-01 Rev. K / August 2010
The measure count (number of readings to take) is set to a
finite value (1 to 99,999) or to infinity. The factory default
value is infinity.
In factory default conditions, the arm layer and scan layer are
transparent to the measurement operation.
2.4 Initial configuration
WAR NI NG
Before turning on the Model 2001, make
sure it is connected to a grounded power
receptacle using the supplied power cord
or the equivalent. Failure to properly
ground the unit creates a shock hazard that
could result in injury or death.
The Model 2001 can save from one to ten user setups in
memory, depending on the installed memory option. You can
select one of the user setups as the power-on default, or have
the instrument power up to either of the two factory defaults
(optimized for “BENCH” or “GPIB” operation). Since the
examples in paragraph 2.5 assume BENCH defaults, reset
the instrument to those settings by performing the following
steps:
1. Press the MENU key to display the MAIN MENU
options as shown below:
MAIN MENU
SAVESETUP GPIB CALIBRATION
TEST LIMITS STATUS-MSG GENERAL
When the lower display line is longer than one line, the
right-most character will be a symbol. Repeatedly
press the key to view the second half of the lower
line, and press the key to return to the first half
display.
Additional information is available for
most front panel operations. Simply press
the INFO key to toggle an INFO display.
Use the and keys to see the
complete lower line.
2. If the SAVESETUP option is not blinking, press the
key until it is and then press ENTER to view the setup
menu:
SETUP MENU
SAVE RESTORE POWERON RESET
3. Press the key until the RESET option of the SETUP
MENU is blinking and then press ENTER to view the
reset menu:
RESET ORIGINAL DFLTS
BENCH GPIB
4. Select the BENCH option by making it blink and
pressing ENTER. The following confirmation message
is displayed:
RESETTING INSTRUMENT
ENTER to confirm; EXIT to abort
5. Press ENTER to confirm. The parameters accessed by
the front panel are now reset to factory defaults for
bench operation. The display will show DC voltage
readings with autorange enabled. The default settings
for DC voltage are:
•Measurement speed (integration time) Normal, 1
power line cycle.
•Digital filter Advanced, 10 readings, 1% noise
tolerance, moving average, enabled.
•Display resolution 6.5 digits.
2.5 Front panel operation
Basic front panel operation will be demonstrated by
examples of measuring DC voltages. The first example
shows readings at default settings and high accuracy
readings. The second example shows storing high speed
readings. These examples are only intended to teach basic
operation.
Details for using the full capabilities of the Model 2001 from
the front panel are contained in Section 3 of this manual. The
manual for the Model 2001-SCAN Scanner Card has
examples for closing and opening channels and scanning
lists of channels.
The front panel operation examples
assume that the Model 2001 is initially set
up for proper operation as explained in
paragraph 2.4.
2.5.1 Measuring DC voltage example
Before starting this example, the front panel display should
show triggered DC voltage measurements. If it does not,
perform a bench reset following the procedure of paragraph
2.4.
Perform the following steps to make DC voltage
measurements with the Model 2001 Multimeter.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Keithley 2001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Keithley 2001 in the language / languages: English as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info