598220
21
Zoom out
Zoom in
Previous page
1/476
Next page
Getting Started
2001-900-01 Rev. K/ August 2010 2-7
2.3.1 Idle
The instrument is considered to be in the idle state whenever
it is not operating within one of the layers of the model. The
front panel ARM indicator is off when the instrument is in
the idle state.
When the Model 2001 is taken out of the idle state by
pressing TRIG (or sending the :INIT or :INIT:CONT ON
command over the IEEE-488 bus), the ARM indicator turns
on and operation proceeds into the arm layer.
2.3.2 Arm layer
In general, the instrument requires an arm event to allow
operation to proceed to the scan layer. With an arm source of
Immediate (the factory default), operation immediately
proceeds to the next layer when the instrument is taken out
of the idle state. With one of the other arm sources selected,
the instrument waits until the appropriate event occurs, as
explained below:
External The instrument waits for an input trigger
(via EXTERNAL TRIGGER connector on rear panel).
•Manual The instrument waits until the front panel
TRIG key is pressed.
•GPIB The instrument waits until a bus trigger (GET
or *TRG) is received.
Trigger Link The instrument waits until an input
trigger is received (via TRIGGER LINK).
•Hold The instrument waits in the arm layer until the
arm source is changed. (Note: the signal and immediate
layer commands, that is, :ARM:LAY1:SIGN and
:ARM:LAY1:IMM, will satisfy the event detection
logic.)
With the Immediate trigger source
selected, a “trigger ignored” message will
be displayed if an external trigger is sent to
the Model 2001 or a manual trigger (i.e.,
pressing TRIG key) occurs. The external
or manual trigger is not used (ignored).
After all scan and measure operations are complete, the
instrument can be returned to the arm layer by programming
the instrument for additional arms. The arm count can be set
to a finite value (1 to 99,999) or to infinity. The factory
default value is one.
After the instrument leaves the arm layer, operation proceeds
into the scan layer.
2.3.3 Scan layer
In general, the instrument requires a scan event to allow
operation to proceed to the measure layer. With a scan source
of Immediate (the factory default), operation immediately
proceeds to the next layer. With one of the other scan sources
selected (External, Manual, GPIB, Trigger Link, Timer, or
Hold), the instrument waits until the appropriate event
occurs.
With a scan source of Timer, the first pass through the scan
layer occurs immediately. If programmed for additional
scans, the instrument waits for an interval between 1msec
and 999,999.999 seconds.
The scan count (number of scans) can be set to a finite value
(1 to 99,999) or to infinity. The “bench” factory default value
is infinity.
With the Immediate trigger source
selected, a “trigger ignored” message will
be displayed if an external trigger is sent to
the Model 2001 or a manual trigger (i.e.,
pressing TRIG key) occurs. The external
or manual trigger is not used (ignored).
After the instrument leaves the scan layer, operation
proceeds into the measure layer.
2.3.4 Measure layer
In general, measure events control the reading rate. With a
measure source of Immediate (the factory default), a device
action occurs immediately. The device action consists of
taking a reading. If scanning is selected, the device action
consists of taking a reading, opening a channel, configuring
for next function in scan list, and closing a channel.
With one of the other measure sources selected (External,
Manual, GPIB, Trigger Link, Timer, or Hold), the instrument
waits until the appropriate event occurs before taking a
reading and, optionally, scanning a channel.
With a measure source of Timer, the first reading is taken
immediately. Each additional reading waits for the Timer to
time out before it is taken.
With the Immediate trigger source
selected, a “trigger ignored” message will
be displayed if an external trigger is sent to
the Model 2001 or a manual trigger (i.e.,
pressing TRIG key) occurs. The external
or manual trigger is not used (ignored).
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Keithley 2001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Keithley 2001 in the language / languages: English as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info