738046

Keiser 3020XP Functional Trainer Manual

12
Zoom out
Zoom in
Previous page
1/20
Next page
12
OPERATION MANUAL
FUNCTIONAL TRAINER
POWER TEST
START TEST: Press and hold both
Thumb Buttons until “6 r” (Test
Mode) displays in the RESISTANCE
window, then release the Thumb
Buttons. NOTE: TARGET REPS window
displays “P1” (Power Test Set 1).
SET RESISTANCE, LOW LEVEL
Set the resistance to 10% of your
maximum.
POWER TEST, SET 1 (P1)
Do one repetition at maximum
speed. Pause 10 seconds.
Repeat two more times.
1
4
2
5
3
6
SET RESISTANCE, HIGH LEVEL
Increase the resistance to a high
level (80-90% of your maximum).
NOTE: TARGET REPS window displays
“P2” (Power Test Set 2).
POWER TEST, SET 2 (P2)
Do one repetition at maximum
speed. Pause 10 seconds.
Repeat 2 more times.
TEST COMPLETE
The ashing number is your
Resistance setting for Maximum
Power.
TROUBLESHOOT: “
Er
” numbers 1 – 4 displayed in the CURRENT POWER window indicates not enough difference in resistance between
the low and high sets. Try again with greater difference in resistance between the low and high sets. To restart the Power Test, (a) reinsert
eChip, if the eChip is being used, or (b) begin at Step 1 to repeat the procedure.
To exit Power Test or resume exercise,
press both Thumb Buttons until “CLEr”
is displayed or remove eChip.
TEST PROTOCOL — The Power Test (KEISER Six-Rep Test) is used to determine the resistance at which you achieve
MAXIMUM POWER. The test consists of two sets:
Perform all repetitions at the highest possible speed at the given resistance; speed is essential in power output.
Note: The Power Test may be performed with or without an eChip. Follow the Power Test instructions below:
Three repetitions
Low resistance, high speed
10% of your maximum
Three repetitions
High resistance, high speed
80-90% of your maximum
SET
2
SET
1
CAUTION
• Test should only be performed with proper instruction.
• Never perform Power Test without proper warm-up.
• Always maintain good form and control throughout test.
• Rate monitoring systems may be inaccurate. Over exercising
may result in serious injury or death. If you feel faint stop
exercising immediately.
• “Current Power,” “Peak Power,” and “Percent of Peak
Power” are not suitable for use in applications where the
health and safety of the patient may be dependent on the
accuracy of those parameters.
• The use of any exercise program requires medical
consultation and compliance with exercise testing guidelines.
You can adjust and test your resistance
setting between the rst and second rep.
The rep count will reset to 1.
You can adjust and test your resistance
setting between the rst and second rep.
The rep count will reset to 1.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Keiser 3020XP Functional Trainer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Keiser 3020XP Functional Trainer in the language / languages: English as an attachment in your email.

The manual is 6,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info