631713
16
Zoom out
Zoom in
Previous page
1/52
Next page
16 of 52
Installation and Connection
Ensure before starting adhesive work that the processing temperature of materials to be glued and the adhesive
sealant is between +5°C and +35°C. Prepare all necessary fastening elements and tools.
Prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube.
Remove the roof duct (Fig.A) and apply the adhesive sealant evenly to the underside of the roof duct ange.
Place the roof duct in the drilled hole and press it rmly against the roof of the vehicle.
Apply the adhesive sealant evenly to the underside of the mounting plate, completely covering the area within the
circular groove (Fig.D). This area of the vehicle roof must be completely coated with adhesive in order to achieve
the necessary bonding force.
Place the mounting plate onto the roof of the vehicle, as you did previously when marking out the drilled holes.
Make sure that the arrow on the mounting plate points forwards in the direction of travel of the vehicle and that
the fastening holes are perfectly aligned with the prepared holes in the roof.
Fasten the mounting plate in place with the prepared screws, evenly tightening six screws across the diagonals.
NOTICE
Risk of material damage due to applying too much force when tightening the screws!
The adhesive sealant used is capable of lling small gaps caused by the curvature of the vehicle roof. If you
apply too much force when tightening the screws, the mounting plate could be bent.
Tighten the screws carefully.
Use a clean colourless cloth to remove any adhesive sealant that leaks out at the sides. Pay attention to the
following:
~ Do not use any cleaning agents or thinners containing solvents, as this could damage the adhesive sealant
applied under the mounting plate.
~ It is recommended to soak the cloth in acetone or MEK. Apply the cloth soaked in acetone or MEK to an incon-
spicuous area to make sure that it does not adversely affect or damage the surface.
~ Use only cleansing paste and water to clean your hands.
Secure the cable gland from inside the vehicle by tightening the ribbed nut supplied (Fig.A).
Note that the curing of the adhesive sealant depends on the ambient temperature and the humidity.
The nal strength is reached only after approx.2days. However, this need not restrict further installation work,
since the mounting plate is held in place by the tightened screws.
5.1.5 Possibilities of the Turntable Installation
Variant with Cable Gland underneath the Turntable
1. Lay the cables supplied with the turntable (2 × coax cables and 1 x power supply cable) into the mounting plate as
indicated by the markings on the mounting plate (see Fig.E1).
2. Feed the remaining lengths of cable through the roof gland into the interior of the motor home / caravan.
3. Lift up the turntable and place it carefully on the mounting plate facing in the direction of travel (see Fig.E2). Make
sure not to step on the plug connector and not to kink / crush the cables.
4. Align the through holes on the turntable with the threaded holes on the mounting plate.
5. Allow the turntable to rest on the front edge of the mounting plate.
6. Keep the turntable supported at an angle (see Fig.E1) and insert a suitable piece of wood underneath it.
7. Lay and connect the turntable cables in the mounting plate as indicated on the mounting plate, see Fig. E1. Take
particular care that the two master coaxial cables, marked red, are connected to each other.
8. Tighten the coaxial cable plugs nger-tight, using no tools.
9. Tighten the coaxial cable plugs lightly using an open-ended 11 AF spanner.
10. Lower the turntable back on to the mounting plate. Make sure that the cables are fed through the cable gland and are
not snagged.
11. Apply a little adhesive sealant to the six threaded holes in the mounting plate and screw the fastening screws into the
thread. Tighten the screws to a torque of 6Nm.
12. To prevent water vapour from inside the vehicle reaching the turntable through the roof gland, thread the three cables
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein CAP 950 - MobiSet 3 Twin at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein CAP 950 - MobiSet 3 Twin in the language / languages: English as an attachment in your email.

The manual is 7,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein CAP 950 - MobiSet 3 Twin

Kathrein CAP 950 - MobiSet 3 Twin Additional guide - English, German - 1 pages

Kathrein CAP 950 - MobiSet 3 Twin User Manual - German - 52 pages

Kathrein CAP 950 - MobiSet 3 Twin Additional guide - Dutch, French, Italian, Turkish, Spanish - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info