631713

Kathrein CAP 950 - MobiSet 3 Twin Manual

15
Zoom out
Zoom in
Previous page
1/52
Next page
15 of 52
3. Provisionally insert the roof duct into the drilled hole (Fig.A).
4. Place the mounting plate on the roof of the vehicle such that the centre hole is positioned centrally to the cable gland.
The arrow symbol ③ must be visible from above and point forwards in the direction of travel of the vehicle (Fig.B).
5. Mark the positions of the six fastening holes on the vehicle roof in a pitch circle.
Tip
The size of the holes and the choice of fastening screws to be used (not included in the scope of delivery)
depend on the type and thickness of the materials used in the roof structure. If the roof panelling (plastic
roofs) is sufciently strong, it is recommended to always use round head screws, plain washers and self-
locking nuts to secure the glued mounting plate.
6. If the roof panel material is very thin and does not provide adequate holding power within the insulation material,
make through holes of Ø5.5 mm into the interior of the vehicle and use galvanised M5 round head screws of suf-
cient length.
Make sure that you use a sufciently strong support that can withstand the bolt tensile forces (large plain washer or a
complete reinforcing plate).
Fig.C
1
2
3
*
)
*
)
*
)
*
)
① adhesive area between the
grooves
② alternative roof fastening
③ washer*)
*
)
Not included in the scope of delivery
7. Create the holes necessary to secure the mounting plate (Fig.C).
8. In addition to the screw connection, the mounting plate and roof duct must be bonded to the roof with adhesive and
sealed. This is done using the DEKAsyl MS adhesive sealant supplied, which is ideally suited for this purpose due to
its broad range of adhesion. Please note the following points:
– Before you start working with the DEKAsyl MS adhesive sealant, it is essential that you have carefully read
through the safety data sheet for the DEKAsyl MS adhesive sealant and the technical data sheet in this
installation manual!
– The prerequisite for good adhesive properties is a clean, dry and grease-free substrate. Therefore, clean the
roof surface with a suitable cleaning agent within a circumference of 17cm around the drilled hole and allow the
surface to dry thoroughly.
– If the surface is painted, ensure that the paint nish is sufciently well bonded to the substrate.
– If the coat of paint is already loose or peeling, remove it down to a stable layer in the area to which the adhesive
will bond. If you have any doubts concerning the adhesive properties, consult a paint and lacquer specialist or the
manufacturer of your vehicle.
9. The procedure for gluing the mounting plate is as follows:
Fig.D
Adhesive area
within the grooves
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein CAP 950 - MobiSet 3 Twin at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein CAP 950 - MobiSet 3 Twin in the language / languages: English as an attachment in your email.

The manual is 7,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein CAP 950 - MobiSet 3 Twin

Kathrein CAP 950 - MobiSet 3 Twin Additional guide - English, German - 1 pages

Kathrein CAP 950 - MobiSet 3 Twin User Manual - German - 52 pages

Kathrein CAP 950 - MobiSet 3 Twin Additional guide - Dutch, French, Italian, Turkish, Spanish - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info