804757
24
Zoom out
Zoom in
Previous page
1/452
Next page
24 English
Note
The travel direction can be changed while
driving. This means that very dull spots can
be polished by moving back and forth sev-
eral times.
1. Assume a seated position.
2. Insert the Intelligent Key.
3. Turn the safety switch to "1".
4. Set the program selector switch to
"TRANSPORT MODE".
5. Set the direction of travel using the drive
direction button on the control panel.
6. Specify the travel speed by pressing the
accelerator pedal.
7. Release the accelerator pedal.
The device stops.
The driving motor is switched off in the event of
an overload. A fault message appears on the
display. If the controller overheats, the affected
power unit is switched off.
8. Allow the device to cool down for at least
15 minutes.
9. Set the program switch to “OFF”, wait
briefly and set to the desired program.
Filling with fresh water
Filling with fresh water via the filling
system
1. Connect the water hose to the connec-
tion nozzle of the filling system (maxi-
mum water temperature 50 °C).
2. Open the water inlet.
3. Monitor the device, the automatic filling
system interrupts the water supply when
the fresh water tank is full.
4. Close the water inlet.
5. Remove the water hose.
Filling with fresh water
1. Open the fresh water tank cap.
2. Fill fresh water (max. 50 °C) to the lower
edge of the filling nozzle.
Note: The fresh water hose can be
clamped with the hose holder during fill-
ing.
3. Close the fresh water tank lock.
Filling with detergent
Notes on detergents
WARNING
Unsuitable detergents
Health risk, damage to the device
Use only recommended detergents. The
operator carries all increased risks relating
to operational safety and increased risk of
accidents if using other detergents.
Use only detergents free of chlorine, sol-
vents, salt and hydrofluoric acid.
Adhere to the safety instructions stated on
the detergent packaging.
Note
Do not use heavily foaming detergent.
Recommended detergents
Filling detergent via the dosing device
Only with DOSE variant:
Detergent is added to the fresh water on
the way to the cleaning head by a dosing
device.
1. Unlock the waste water tank and pivot it up.
2. Fill the detergent canister with detergent.
3. Pivot the waste water tank forwards.
Note
A maximum of 3% detergent can be added
with the dosing device. If the dosage is
higher, the detergent must be added to the
fresh water tank.
Filling the detergent into the fresh water
tank
1. Fill the detergent into the fresh water tank.
Note: The lid for the filling hole of the
fresh water tank can be used to measure
the detergent. It has a measuring scale
marked on the inner side.
Adjusting parameters
1. Set the program switch to the desired
cleaning program.
2. Turn the Info button until the desired pa-
rameter is displayed.
3. Press the Info button.
The adjusted value flashes.
4. Set the desired value by turning the Info
button.
5. Confirm the changed setting by pressing the
Info button or wait until the set value is auto-
matically accepted after 10 seconds.
Yellow Intelligent Key
The yellow Intelligent Key authorizes func-
tions that are required for the cleaning task.
The parameters for the various cleaning pro-
grams are preset in the device. Individual pa-
rameters can be changed depending on the
authorization of the yellow Intelligent Key.
The display texts for parameter setting are
largely self-explanatory.
"FACT" parameters (only available with R
cleaning head):
"Fine Clean": Low brush speed for re-
moving grey film from fine stone.
"Whisper Clean": Medium brush speed
for maintenance cleaning with reduced
noise level.
"Power Clean": High brush speed for
polishing, crystallizing and sweeping.
Adjusting the suction bar
Adjusting the inclination
The inclination must be adjusted so that the
suction lips of the suction bar make even
contact with the floor over the entire length
of the suction bar.
1. Park the device on a surface without a
slope.
2. Turn the program switch to the "Vacu-
um" position.
3. Drive the device a small distance for-
wards.
4. Read the spirit level.
1Screw
2Nut
3Spirit level
5. Unscrew the nut.
6. Adjust the screw so that the spirit level
indicator is between the two lines.
7. Tighten the nut.
8. To check the new setting, move the de-
vice forward again a short distance. Re-
peat the adjustment process if
necessary.
9. Turn the key-operated switch to "OFF".
Adjusting the height
The height adjustment affects the bending
of the suction lips on contact with the floor.
Note
Standard setting: 3 washers above, 3
washers below the suction bar.
Uneven floor: 5 washers above, 1 washer
below the suction bar.
Very smooth floor: 1 washer above, 5
washers below the suction bar.
1. Unscrew the nuts.
1Nut
2Washer
´
3Spacer roller with holder
Application Detergent
Maintenance cleaning of all
water-resistant floors
RM 746
RM 756
RM 780
Maintenance cleaning of
polished hard surfaces (e.g.
granite)
RM 755 es
Maintenance cleaning, in-
termediate cleaning and ba-
sic cleaning of industrial
floors
RM 69 ASF
Maintenance cleaning and
basic cleaning of fine stone
tiles
RM 753
Maintenance cleaning of
tiles in sanitary areas
RM 751
Coating removal on all alka-
line-resistant floors (e.g. PVC)
RM 752
Coating removal on linole-
um floors
RM 754
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher B 110 R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher B 110 R in the language / languages: All languages as an attachment in your email.

The manual is 30.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info