804757
25
Zoom out
Zoom in
Previous page
1/452
Next page
English 25
2. Place the desired number of washers
between the suction bar and the spacer
roller.
3. Fit the remaining unused washers above
the spacer roller.
4. Screw on the nut and tighten.
5. Repeat the entire procedure at the sec-
ond spacer roller.
Note
Set both spacer rollers to the same height.
Adjusting the squeegee blades
The squeegee blades only need to be ad-
justed on the D cleaning head.
1. Adjust the squeegee blades by turning
the setting wheel so that the squeegee
blade touches the ground.
2. Turn the adjustment wheel an additional
1 rotation down.
Cleaning
1. Sit on the seat.
2. Insert the Intelligent Key.
3. Set the safety switch to "1".
4. Set the travel direction switch to forward
travel.
5. Set the program switch to the desired
cleaning program.
6. Determine the speed with the accelera-
tor pedal.
7. Determine the travel direction with the
steering wheel.
8. Drive over the surface to be cleaned.
Side scrubbing deck (option)
The side scrubbing deck makes working
close to the edge easier.
Note
The side scrubbing deck is not active in the
polish and vacuum cleaning programmes.
1. Operate the side scrubbing deck switch.
The side scrubbing deck is activated.
2. To finish working with the side scrubbing
deck, set the side scrubbing deck switch
to "0" .
Finishing operation
Finishing cleaning
1. Set the programme switch to Drive.
2. Continue moving a short distance.
The residual water is vacuumed up.
3. Turn the key-operated switch to "OFF".
4. Remove the Intelligent Key.
5. Charge the battery if necessary.
Draining the waste water
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment
regulations.
Note
When the waste water tank is full, the suc-
tion flow is interrupted by a float to prevent
the waste water tank from overflowing. In
this case, drain the waste water.
1. Remove the waste water drain hose
from the support and open the drain
hose cover.
2. Squeeze the end of the hose and lower
it over the disposal facility.
3. Adjust the strength of the waste water jet
by squeezing the end of the hose.
4. Rinse the waste water tank with clear
water.
5. Close the drain hose cover.
6. Press the waste water hose into the sup-
port on the device.
Waste water tank rinsing system
(option)
1. Remove the waste water drain hose
from the support and open the drain
hose cover.
2. Close the cover of the waste water tank.
3. Connect a water supply hose to the wa-
ter connection of the waste water tank
flushing system.
4. Open the water inlet and rinse the waste
water tank for about 30 seconds.
5. Repeat the rinsing process 2 to 3 times
if necessary.
6. Close the water inlet.
7. Disconnect the water supply hose from
the device.
8. Close the waste water drain hose and
press it into the support.
Empty the coarse dirt container
1. Lift the coarse dirt container and pull it out.
2. Empty the coarse dirt container.
3. Reinstall the coarse dirt container.
Draining fresh water
1. Open the fresh water tank cap.
2. Drain the fresh water.
3. Clean the filter.
4. Fit the fresh water tank cap.
Shutting down the unit
1. Turn the key-operated switch to "OFF".
2. Remove the Intelligent Key.
3. Secure the device against rolling away.
4. Open the lid of the waste water tank and
secure it with the support so that the
waste water tank can dry out. To do this,
swing the support down and position the
lower end at the desired level when
swinging down the cover.
1Waste water tank cap
2Support
3level
5. Charge the battery if necessary.
Grey Intelligent Key
The grey Intelligent Key grants the supervi-
sory staff extended authorizations and set-
ting options.
1. Insert the Intelligent Key.
2. Select the desired function by turning
the info button.
Transport journey
1. Set the program selector switch to
"TRANSPORT MODE".
2. Press the Info button.
The following functions can be executed
from the TRANSPORT MODE menu:
Set maximum speed
Show operating hours counter
Clearing the maintenance counter
Show software versions
Adjust the R or D cleaning head
Switch speed-dependent water dosage
on / off
Setting after-running times
Setting the language
Key management
Switch attachment kits on / off
Activate factory setting
Maximum speed
The maximum speed can be limited in the
"max speed" menu.
1. Turn the info button until "max speed" is
shown on the display.
2. Press the Info button.
3. Turn the info button until the desired
maximum speed is displayed.
4. Press the Info button.
Note
The working speed cannot exceed the
maximum speed set.
Resetting the maintenance counter
If maintenance work shown in the display
has been carried out, the corresponding
maintenance counter must then be reset.
1. Turn the Info button until "maintenance
count." is displayed.
2. Press the Info button.
The counter readings are displayed.
3. Turn the info button until the counter to
be cleared is highlighted.
4. Press the Info button.
5. Select "yes" by turning the Info button.
6. Press the Info button.
The counter is cleared.
Adjusting the cleaning head
1. Turn the Info button until "brush head" is
displayed in the menu.
2. Press the Info button.
3. Turn the info button until the type of the
built-in cleaning head is highlighted.
“Roll" = R cleaning head
"Disc" = D cleaning head
4. Press the Info button.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher B 110 R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher B 110 R in the language / languages: All languages as an attachment in your email.

The manual is 30.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info