780095

Kalkhoff Rohloff SpeedHub 500-14 Manual

33
Zoom out
Zoom in
Previous page
1/114
Next page
75
123
A T T E N T I O N
4
Whenmounting,makesurethe
shiftercablehousingsarenot
pinchedbeforemountingthe
ferrules. Thiswillensurethecables
arewellprotectedfromdirtand
moisture.
7. Cable routing
7.1 Shifter cables ( Set 1.8mArt. #8268 / 2.5mArt. #8267)
Cable Manager Kit (Art. #5201)
For problem-free cable routing, a
special cable manager kit that holds
one shifter cable neatly in position is
available from . It provides a
tidy method of holding the shifter
cables even on frames without cable
guides. The cablehousing can be
easily removed when replacing
cables.
Rohloff
Theshiftercableseachcomprise
ofaspirallywoundsteelouter
housing(diameter4.7mm)with
integratednylonliner,a1.1mm
stainless-steelshiftercablewith
cylindricalnipple(diameter
4 5mm)andfoursealedcable
housingferrules.
x
Thecablehousingferrulereduces
thechancesofdirtandmoisture
enteringboththeshiftercablesand
twistshifter.
Thespiralhousingoftheshifter
cablesgivesapositivefeelingto
thegearchangethroughthetwist
shifter.Othershiftercable
housings(e.g.SIScables)reduce
thispositivefeeling.
Theshiftercablesaretobe
mounteddry(freefromoilor
grease). Thenylon-stainlesssteel
combinationrunsservicefree.
P O I N T E R
Mounting
76
D
C
B
A
D
1 2 3
Whenroutingtheshiftercablesof
theinternalgearmechalongthe
toptube,thecableguideis
mountedtothebrakeboss.Priorto
routingthecables,thecableguide
mustbesecuredtotheleftside
brakeboss. Theoriginalbrakeboss
securingboltmustberemoved
(thiswillbereplacedwiththenew
boltsupplied). Allotherpartsof
thebrakeremaininplace.
Cableguide13°:
Cableguide
Mountingbolt(M6 25)
Cableadjuster(2 )
Spacer
Spacer mustbeusedwhen:
Mountingboltistoolongfor
securingtothebrakeboss
Cableguide interfereswith
thesmoothrunningofthebrake
operation(egparallelpush
linkagecertaintypesof V-brake
system).
A
B
C
D
D
A
x
x
-
-
Fitthemountingboltthroughthe
cableguide(andspacer,when
necessary)andscrewintothe
brakebosswithalittlegrease
(4mmallenkey,tighteningtorque:
6Nm/51in.lbs.).Holdthecable
guideinpositionwitha13mm
wrench.
Hubcable1
Shiftercable14
Twistshifter
Cableguide
Hubcable14
Shiftercable1
7.2 Internal gear mech
7.2.1 Cable routing via the brake boss
With the internal gear mech, the shifter cables run from the twist shifter to the cable guide. This could be located on
the brake boss or by frame clamp on the chainstay. The minimum distance from the axle to the cable guide is 240mm.
Whenpullingtheshiftercable1,
lowergearsareengaged. When
pullingtheshiftercable14,higher
gearsareengaged.
Gearcable1liestothefrontofthe
twistshifteraswellastothefront
ofthecableguide.Gearcable14
liestothebackofthetwistshifter
aswellastothebackofthecable
guide.
Mounting
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalkhoff Rohloff SpeedHub 500-14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalkhoff Rohloff SpeedHub 500-14 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 40.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info