778421
44
Zoom out
Zoom in
Previous page
1/70
Next page
EN-44 Originalbetriebsanleitung Allgemein
11. If the chain can only be moved with diculty to the
next larger cog, you will need to increase the tensile
stress. If the chain can only be moved with diculty to
the next smaller cog, the tensile stress must be
decreased.
12. The tensile stress can
be adjusted using
the cable adjustment
screw on the control
elements.
Turn the cable
adjustment screw
clockwise to
increase the tension.
Turn the cable
adjustment screw
counterclockwise to decrease the tension. The tensile
stress should only be high enough to prevent the chain
from rubbing on the next higher cog.
Rear derailleur: setting the lower stop
13. Shift the chain to the largest chainring and the
smallest sprocket using the control elements on the
handlebars.
14. Now, turn the lower adjustment screw until the idler
pulley is positioned exactly beneath the largest
chainring.
Fig. 83 Adjusting the tensile
stress ©Shimano
Cable adjustment screw
Front derailleur: setting the upper stop
1. Shift the chain to the smallest chainring and the
largest sprocket using the control elements on the
handlebars.
2. The distance between the chain and the inner guide
plate should now be minimal. The chain should not
touch the guide plate.
3. This distance can be reduced using the lower screw
(L). Turning this clockwise moves the front derailleur
outward towards the crank, provided that the tensile
stress on the cable is already high enough. Turning
this counterclockwise moves the front derailleur
towards the frame.
4. To set the correct tensile stress, shift to the large
chainring at the front and the smallest sprocket at the
rear using the control elements on the handlebars.
The chain should not touch the outer plate of the front
derailleur.
5. The tensile stress can be adjusted using the cable
adjustment screw. Turn the cable adjustment screw
clockwise to increase the tension. Turn the cable
adjustment screw counterclockwise to decrease the
tension. The tensile stress should only be high enough
to prevent the chain from rubbing on the next higher
cog, and the guide plates of the front derailleur from
touching the chain.
Fig. 84 Adjustment screws ©Shimano
Derailleur
Adjustment screws
Front derailleur: setting the upper stop
6. To set the upper limit, turn the upper screw (H).
Turning this clockwise moves the front derailleur
closer to the frame. Turning this counterclockwise
moves the front derailleur away from the frame.
7. The outer guide plate of the front derailleur should
now run parallel to the chainring. The distance
between the outer guide plate and the largest teeth of
the chainring should be between 1 and 3 mm.
24.3.3.2 Shimano Ultegra Di2 electronic
derailleur
Setting the rear derailleur
1. Shift the chain to the smallest chainring and the
largest sprocket using the control elements on the
handlebars, and turn the crank arm to the rear.
2. Then, turn the adjustment
screw to bring the
idler pulley as close as
possible to the sprocket
without them touching.
3. Now, shift the chain to
the smallest sprocket
and repeat these steps
to ensure that the pulley
does not touch the
sprocket.
4. Shift the rear derailleur
using the buttons on the
right-hand gear lever to
sprocket 5.
Fig. 85 Adjustment screw
©Shimano
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalkhoff 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalkhoff 2021 in the language / languages: English as an attachment in your email.

The manual is 5.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalkhoff 2021

Kalkhoff 2021 User Manual - German - 72 pages

Kalkhoff 2021 User Manual - Dutch - 71 pages

Kalkhoff 2021 User Manual - French - 74 pages

Kalkhoff 2021 User Manual - Spanish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info