136123
77
Zoom out
Zoom in
Previous page
1/84
Next page
77
CORRECTIVE ACTION
Position the camcorder so its
microphone is away from the TV.
Turn the TV’s volume down.
If you need the skipped channels,
restore them ( pg. 66).
Press PAUSE to pause the recording,
change channels, then press PLAY to
resume recording.
Perform manual setting again.
Turn off the recorder once and connect
the TV aerial cable to the recorder
properly, then turn on the recorder
again. The recorder will try Auto Set
Up again ( pg. 8).
Turn off the recorder once and connect
the fully-wired 21-pin SCART cable to
the recorder properly, then turn on the
recorder again. Then perform Preset
Download again ( pg. 9).
Re-set the remote control to the
correct brand ( pg. 53, 54).
Turn off the recorder or the con-
nected appliance once, then turn it
on again.
SYMPTOM
1. Whistling or howling is heard from
the TV during camcorder record-
ing.
2. When scanning channels, some of
them are skipped over.
3. The channel cannot be changed.
4. Channel settings that were made
manually seem to have changed or
disappeared.
5. No channels are stored in the
recorder's memory.
6. The remote control won’t operate
the TV or satellite receiver.
7. No picture appears when you
connect an appliance to DV IN/
OUT connector.
POSSIBLE CAUSE
The camcorder’s microphone is too
close to the TV.
The TV’s volume is too high.
Those channels have been desig-
nated to be skipped.
Recording is in progress.
After the manual settings were
made, Auto Channel Set was
performed.
The TV aerial cable was not
connected to the recorder when
Auto Set Up was performed.
The fully-wired 21-pin SCART cable
was not connected between TV and
the recorder when Preset Download
was performed.
The remote control brand setting is
incorrect.
OTHER PROBLEMS
CORRECTIVE ACTION
Check the programmed data and re-
program as necessary, then press
again.
The programme may not have been
recorded in its entirety. Next time
make sure you have enough time on
the tape to record the entire
programme.
Refer to "Guide Program Number Set"
and re-perform the procedure
( pg. 73).
SYMPTOM
5. "" blinks for 10 seconds and the
Timer mode is disengaged.
6. The cassette is automatically
ejected, the power shuts off and
"" and "]" won’t stop blinking.
7. The VIDEO Plus+ system does not
timer-record properly.
POSSIBLE CAUSE
has been pressed when there are
no programs in memory, or the timer
record information has been
programmed incorrectly.
The end of the tape was reached
during timer recording.
The recorder’s channel positions
have been set incorrectly.
TIMER RECORDING
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr dvs 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr dvs 2 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info