533229
29
Zoom out
Zoom in
Previous page
1/48
Next page
EN
29
USING THE REMOTE CONTROL UNIT
Audio Dubbing
The audio track can be customized only when recorded
in the 12-bit mode ( pg. 21).
NOTES:
Audio Dubbing is not possible on a tape recorded in
16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
To perform Audio Dubbing while watching on the
television, make connections ( pg. 15).
1 Play back the tape to locate the point where editing
will start, then press PAUSE (6) T.
2 While holding A.DUB (e) j on the remote control,
press PAUSE (6) T. 6e y and MIC (GR-D31 only)
appear.
3 Press PLAY (
4
) h, then begin narrating.
Speak into the microphone.
To pause dubbing, press PAUSE (6) T.
4 To end Audio Dubbing, press PAUSE (6) T, then
STOP (5) O.
To hear the dubbed sound during playback . . .
..... set 12BIT MODE to SOUND 2 or MIX in the
Menu Screen ( pg. 25).
NOTES:
Sound is not heard from the speaker during Audio
Dubbing.
When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
If feedback or howling occurs during TV playback, move
the camcorders microphone away from the TV, or turn
down the TVs volume.
If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (
pg. 44).
To perform Audio Dubbing with a video unit connected to
the camcorders AV connector, first set S/AV INPUT to
ON in the Menu Screen (GR-D31 only,
pg. 24).
AUX appears instead of MIC.
Insert Editing
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
NOTES:
Before performing the following steps, make sure that
TIME CODE is set to ON in the Menu Screen
(
pg. 24, 25).
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
To perform Insert Editing while watching in the television,
make connections ( pg. 15).
1 Play back the tape, locate the Edit-Out point and
press PAUSE (6) T. Confirm the time code at this
point ( pg. 24, 25).
2 Press REW (
2
) U until the Edit-In point is located,
then press PAUSE (6) T.
3 Press and hold INSERT (w) I on the remote
control, then press PAUSE (6) T. 6w & and the
Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.
4 Press START/STOP a to begin editing.
Confirm the insert at the time code you checked in
step 1.
To pause editing, press START/STOP a. Press it
again to resume editing.
5 To end Insert Editing, press START/STOP a, then
STOP (5) O.
NOTES:
Programme AE with special effects ( pg. 16) can be
used to spice up the scenes being edited during Insert
Editing.
During Insert Editing, the date and time information
changes.
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops (
pg. 44).
Stereo microphone
9
0
2
3
4
6
we
5
T
W
W
E
U
R
I
Y
k
g
f
T
O
P
d
s
j
l
;
a
h
GR-D31/21EK 28-33 02.12.19, 9:14 PM29
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D31 in the language / languages: English as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info