614555
41
Zoom out
Zoom in
Previous page
1/51
Next page
– 39 –
Foot lift function after thread trimming (Function setting No. 55)
This function can automatically lift the presser foot after thread trimming. This function is effective only
when it is used in combination with the AK device.
n.
55
0 : OFF Function of automatically lifting the presser foot is not provided.
(Presser foot does not automatically go up after thread trimming.)
1 : ON Function of automatically lifting the presser foot is provided.
(Presser foot automatically goes up after thread trimming.)
Reverse revolution to lift the needle after thread trimming (Function setting No. 56)
This function is used to make the sewing machine rotate in the reverse direction after thread trimming to
lift the needle bar almost to highest position.
Use this function when the needle appears under the presser foot and it is likely to make scratches on the
sewing products of heavy-weight material or the like.
n.
65
0 : OFF Function of making the sewing machine rotate in the reverse direction to lift the
needle after thread trimming is not provided.
1 : ON Function of making the sewing machine rotate in the reverse direction to lift the
needle after thread trimming is provided.
(Caution) The needle bar is raised, by rotating the machine in the reverse direction, almost to the
highest dead point. This may result in slip-off of the needle thread. It is therefore necessary
to adjust the length of thread remaining after thread trimming properly.
Function of holding predetermined upper / lower position of the needle bar (Function setting No.
58)
When the needle bar is in the upper position or in the lower position, this function holds the needle bar by
applying a brake slightly.
n.
85
0 : OFF Not provided with the function of holding predetermined upper/lower position of
the needle bar
1 : ON Provided with the function of holding predetermined upper/lower position of the
needle bar (Holding force is weak.)
2 : ON Provided with the function of holding predetermined upper/lower position of the
needle bar (Holding force is medium.)
3 : ON Provided with the function of holding predetermined upper/lower position of the
needle bar (Holding force is strong.)
Change-over function of AUTO / Pedal for sewing speed of the reverse feed stitching at the start of
sewing (Function setting No. 59)
This function selects whether the reverse feed stitching at the start of sewing is performed without a break
at the speed set by the function setting No. 8 or the stitching is performed at the speed by the pedal oper-
ation.
n.
95
0 : Manual The speed is indicated by the pedal operation.
1 : Auto Automatic stitching at the specied speed
(Caution) 1. The max. sewing speed of the reverse feed stitching at the start of sewing is limited to the
speed set by the function setting No. 8 regardless of the pedal.
2. When “0” is selected, stitches of reverse feed stitching may not match those of normal
feed stitching.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki DDL8700B-7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki DDL8700B-7 in the language / languages: English as an attachment in your email.

The manual is 6,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info