30210

JRpropo XP8103 Manual

18
Zoom out
Zoom in
Previous page
1/142
Next page
XP8103 17
For proper DSC hook up and operation:
1. Leave the transmitter power switch in the OFF position. The
transmitter will not transmit any radio frequency (RF) in this
position.
2. Plug the DSC cord (optional) into the DSC port in the rear of
the transmitter.
3. The encoder section of the transmitter will now be
operational and the LCD display will be lit.
4. Plug the other end of the DSC cord into the receiver charge
receptacle. Turn the switch harness to the ON position.
Note: The DSC function will only operate with the JRPA001
Deluxe Switch Harness, or the JRPA004 Charge Switch.
When you install the charging jack, be sure to hook the
charging jack receptacle securely into the switch harness charge
cord.
Why you should use the DSC function:
1. The DSC enables you to check the control surfaces of your
airplanes without drawing the fully operational 200 mAh from
your transmitter battery pack. Instead, you will only draw 70
mAh when using the DSC function.
2. The DSC function allows you to make final adjustments to
your airplane without transmitting any radio signals. Therefore, if
another pilot is flying on your frequency, you can still adjust your
airplane and not interfere with the other pilot’s aircraft.
Note: Under no circumstances should you attempt to fly your
airplane with the DSC cord plugged in! This function is for
bench checking your airplane only.
5.4 DSC Cord
An eyelet is provided on the face of the XP8103 transmitter
which allows you to connect a neck strap (JRPA023). This hook
has been positioned so that your transmitter has the best possible
balance when you use the neck strap.
Note: Double check to ensure that the neck strap is securely
fastened to the transmitter.
5.5 Neck Strap Adjustment
An optional base loaded antenna is available for use with the
XP8103 transmitter. It is considerably shorter than the standard
antenna. However, the base loaded antenna cannot be
collapsed for storage in the side of the transmitter. You must also
use an adaptor (JRPA156) to attach the antenna to your XP8103.
The base loaded antenna (JRPA155) is made of a flexible coil
and is covered with a soft plastic material. Your range will not
be affected when using the base loaded antenna.
5.6 Base Loaded Antenna
A
B
C
A. Charge cord/DSC receptacle
B. Switch harness lead
C. Charge cord/DSC lead
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo XP8103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XP8103 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info