606954
34
Zoom out
Zoom in
Previous page
1/112
Next page
32
Gyro▋Sensitivity【GYRO▋SENS
Function▋Explanation
This function controls the gyro sensitivity using the GEAR channel, and the Auxiliary (AUX)
channel if required. It allows adjusting the gyro sensitivity from the transmitter. Further, it
supports “Dual Gain” as employed in JR’s G7000 where two channels are required. Additionally,
the use of two gyro units is also possible. In addition, it supports 3 axis gyros (such as JR
TAGS01), with separate gains for yaw, pitch and roll axis. The sensitivity switching of each gain
can be with individual switches, or combined using the Flight Mode switch.
Setting▋Method
It is necessary to allocate the Gyro Sensitivity to a channel using “DEVICE SELECT” in the System List. Set “OUT”
as “GYRO” by activating the function.
Select the switch position for changing the gyro sensitivity and move the cursor to each position to set the
sensitivity on the display. If AUTO” is selected, the sensitivity switching setting for each flight mode will be
applied.
There are two gyro sensitivities available - “NORMALand Tail Lock (T.LOCK) - choose the type depending on
your application.
Gyro sensitivity Switching delay (DELAY)
To avoid excessive servo hunting when switching
the gyro sensitivity from a low sensitivity to
higher sensitivity setting, (e.g. when the main
rotor blade rpm is not stable) it is possible to set
a delay on this function.
Note: During switching, the time will be delayed
only in the high sensitivity direction.
Trim Input Function (TRIM IN)
By using the Trim Input, it is possible to change
the gyro sensitivity values using a Trim Lever.
Therefore, it is possible to easily adjust the sensitivity during ight.
When two individual channels have been selected for Gyro sensitivity, it is possible to select from the following two
modes.
"TWO GYRO"
It is possible to allocate two individual gyro sensitivities, and the Gyro sensitivity switching can occur on one
shared switch.
"DUAL GAIN"
In this mode, one channel is allocated for “NORMAL” and the other channel to “TAIL LOCK SENSITIVITY.
For 3 Axis gyro applications (such as the JR TAGS01) three separate gain channels can be used. Each
sensitivity for yaw, pitch and roll axis can be set using individual switches, or combined onto the ight mode
switch. The gyro sensitivities can also be changed to Normal or Stunt Modes when using the JR TAGS01.
“Calibration for 3 Axis Gyros”
The JR 3 Axis Gyro system (TAGS01) as used for Flybarless R/C helicopters requires “CALIBRATION” prior
to ying. This is required to recognize the type of CCPM being employed, and learn the servo travel ranges
used. Calibration requires precise gimbal stick movement of one function at a time (Elevator or pitch stick up
& down, and Aileron stick right to left). If, for example, the aileron stick is pushed by mistake during elevator
calibration, the calibration will be incorrect. In order to avoid this problem, the calibration function allows
single channel calibration.
Function▋List
Helicopter
Airplane
DANGER
WARNING
CAUTION
Glider
Sensitivity Switching delay
If AUTO is selected, the sensitivity
switching setting for each Flight
Mode will be applied.
Further, by operating the switch
that you wish to use, input will be
automatically carried out.
Display for corresponding
flight mode
Gyro Mode selection
S = STUNTT = TAIL LOCKN = NORMAL
Gyro sensitivity (T.LOCK)
Calibration function
TRIPLE AXIS MODE
Setting values and actual output values
NORMAL
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 125%
T.LOCK
T
N
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
0%50%100%150%
TRIPLE AXIS
S
N
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
0%50%100%150%
DUAL GAIN
NORM GAIN
T.LOCK
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 125%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
The upper numerical values are the
setting values.
Sensitivity Switching delay
If AUTO is selected, the sensitivity
switching setting for each Flight
Mode will be applied.
Further, by operating the switch
that you wish to use, input will be
automatically carried out.
Display for corresponding
flight mode
Gyro Mode selection
S = STUNTT = TAIL LOCKN = NORMAL
Gyro sensitivity (T.LOCK)
Calibration function
TRIPLE AXIS MODE
Setting values and actual output values
NORMAL
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 125%
T.LOCK
T
N
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
0%50%100%150%
TRIPLE AXIS
S
N
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
0%50%100%150%
DUAL GAIN
NORM GAIN
T.LOCK
-150% -100% -50% 0% 50% 100% 150%
0% 50% 100% 125%
0% 50% 100% 150%
-150% -100% -50% 0% 50% 100% 150%
The upper numerical values are the
setting values.
XG14English.indd 32 2013/07/16 16:40
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo XG14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XG14 in the language / languages: English as an attachment in your email.

The manual is 25,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info