606954
33
Zoom out
Zoom in
Previous page
1/112
Next page
31
Throttle▋hold【THRO▋HOLD
Function▋Explanation
This function is for autorotation landings it holds the Throttle Servo at a low position. Using
a selected switch, the engine can be cut, or xed at an optional slow position. Further, there is
also a Stick Auto function that allows switching of the servo to the Hold position when the stick
is lowered to a preset position.
Setting▋Method
This function is “INH” by default. Set the function to ACT. Then adjust the hold position as required. The Hold
switch is used by default, but this selection can be modied
By default, the “HOLD SW” is allocated to POS1. It is possible to allocate this switch to any desired switch
locations.
Stick Auto Function (STICK AUTO)
When “STICK AUTO” is set, the servo will change to the Hold position when the stick is lowered past a
predetermined position. To deactivate this function simply turn o󰮏 the allocated switch.
Initially this function is inhibited. To activate this function, move the cursor to “INH”, and press the dial to
ACT. Move the cursor to the inversed display next to STICK AUTO, Move the throttle stick to desired position
and press the “STO” key to set the position (a numerical value between 0-100 will be displayed on the inversed
display).
To “INH” this function, press the CLR key while the display is inversed.
Hold delay function (DELAY)
It is possible to set a “DELAY“ to prevent a sudden increase in engine rotations when the Hold switch is set to
OFF. The duration of the delay can be set between 0.1sec to 2.0sec.
If the Hold Delay is set, any throttle setting in the Servo Speed function will be cancelled.
By setting throttle hold active, this function acts like an additional ight mode. It is possible to set dedicated
Dual rates, Pitch Curve, etc to this function.
Caution▋Note
After the setting, operate the servos and carefully conrm each of the Flight Mode settings before ying.
Function▋List
Helicopter
Airplane
DANGER
WARNING
CAUTION
Glider
Operation condition
In order to use the function,
INH should be changed to ACT.
Stick Auto functionStick Auto functionHold Delay function
Hold Delay function
ダイヤ
TIPS
調整ポイント表示
ポイント接続を曲線に変更 スティック入力位置と出力位置の数値表示
現在の
フライトモード位置
各調整ポイントの
入力位置と出力位置
ポイントの
追加と削除
注意:
グラフはホバリン
グスロットルやス
ロットルトリムで
変化する場合もあ
ります。
カーブをコピー
XG14English.indd 31 2013/07/16 16:39
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo XG14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XG14 in the language / languages: English as an attachment in your email.

The manual is 25,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info