Manual JRpropo PCM9X (page 44 of 48) (English)

30203

Zoom out

Zoom in

1/48

4242

Assigning Channels

Using the scroll bar, move the cursor to the master channel. Press scroll bar

down to activate selection. Roll the scroll bar to select the desired channel.

Repeat this process to select the slave channel.

Origin Mixing

When origin mixing is activated any dual rate, exponential or other modifier

applied to the master channel is ignored on the slave channel. Therefore the

same dual rate, etc, modifiers are not present on the slave channel when a

command is inputted, they are only present on the master channel.

Assigning Mix Value

Using the scroll bar position the cursor over POS0 and click. Move the master

channel to highlight either the top or bottom figure. Increase or decrease the

mix value by rolling the scroll bar. Use the CLR key to reset the mix value to

zero. Complete the input by clicking the scroll bar. When activating the mix

with a switch, different mix values may be input for both switch position 0 and

switch position 1.

Establishing Offset

The purpose of the mixing offset is to redefine the neutral position of the

slave channel. Any desired position may be set for the offset reference point.

Position the cursor over Offset and click. Roll the scroll bar to input a value, in

steps of 2, between –170 and +170.

Operating with a switch

Position the cursor over the required switch and click to enable that switch.

The dark square moves to the top position (POS1) as a confirmation. More

than one switch may be selected if required.

Activation by Throttle Stick Position

Click the scroll bar with THRO STK selected. Roll the scroll bar to select a

throttle stick activation position between 0% and 100% or to inhibit (INH).

Note that the stick resolution has 200 steps so that two clicks of the scroll bar

are required to change the percentage displayed.

Failsafe

The failsafe/hold function is only available with PCM modulation. If you

have selected PPM modulation, the fail-safe screen will not appear.

Z-PCM modulation mode.

All channels can be HOLD or can take a pre-selected position. Three fail-safe

time delays are available. Select your chosen delay (0.2, 0.5 or 1.0 second) by

using the scroll bar to select the desired setting. For a pre-selected position

move the transmitter controls to the desired fail-safe position (throttle stick

low!) and store the settings by pressing the CLEAR key. A beep will sound to

confirm that the fail-safe positions have been stored.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo PCM9X in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JRpropo PCM9X Manual

Product: