472825

Janome DC5100 Manual

24
Zoom out
Zoom in
Previous page
1/60
Next page
20
Using the seam guides on the needle plate
q Needle drop position
w Edge of fabric
e Needle plate guide line
The seam guides on the needle plate are engraved to help
you measure seam width. The numbers on the needle plate
indicate the distance between the center needle position
and the edge of the fabric. The lines are 1/8˝ (0.3 cm)
apart, and engraved at 3/8˝, 4/8˝, 5/8˝ and 6/8˝. The lines in
millimeters are 5 mm apart, and are engraved at 10 mm,
15 mm and 20 mm.
Turn a square corner
q Cornering guide
w Up/down needle position button
e Presser foot lifter
When sewing with fabric edge at 5/8˝ seam guide, to turn
a square corner so that sewing continues at same distance
from edge.
1. Stop stitching when front edge of fabric reaches the
cornering guide lines q.
2. Lower the needle by pressing up/down needle position
button w.
3. Raise the presser foot e and turn the fabric
counterclockwise 90°.
4. Lower the presser foot, and begin stitching in the new
direction.
q Quilter holding screw
w Quilter
e Hole
r Distance
Use the seam guide lines on the needle plate, and the
free-arm, to help determine the distance between quilting
stitches. The quilter will help keep the stitching line straight.
z Loosen the quilter holding screw q on the back of the
presser foot as shown.
x Slide the quilter w into the hole e under the screw to
the width of quilting stitches you desire width.
c Tighten the screw q.
v Sew guiding the quilter over the previous row of
stitching.
q
w
e
q
e
w
Quilting
q Stitch pattern: 01
w Needle thread tension: 2 to 6
e Presser foot: Zigzag foot: A
r Presser foot: Straight stitch foot: H
t Quilter
q w ert
NOTE:
When using the straight stitch foot, make sure to use
the center needle position. Otherwise the needle may
strike the presser foot and possibly break.
w
e
q
r
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome DC5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome DC5100 in the language / languages: English as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info