Manual Inverto IDLV-4000P (page 16 of 38) (English)

509862

Zoom out

Zoom in

1/38

ASI2/SDI

You can choose between ASI output and SDI output.

If the port is congured as ASI2, the conguration method is the same as ASI.

If the port is congured as SDI, there are two parameters which need to be set:

‘Audio PID’ and ‘Embed Audios’.

Audio PID: Press the <↑> <↓>-keys to choose the audio PID from 1~4.

Embed Audios: There are 4 options: none, one&two, two, and one.

Mux / Filter

The Mux or Filter menu is shown only when the Mux/Filter function block is en-

abled and turned on. The Mux / Filter are alternative.

Make sure the s/w supports Mux / Filter function. The earlier s/w has masked

the Mux / Filter function. After s/w: 03.9a.xx, this Mux / Filter function has been

unmasked.

Mux function description

Mux Switch: The internal multiplexer could be switched On/Off. The default

value is ‘off’. To activate the re-Multiplexing function, you should turn on the Mux

functional block.

Bit Rate: Should be set to a specied value that doesn’t exceed the Maximum

physical limit of the output medium. For example, to deliver the multiplexed TS

to an 8MHz DVB 256QAM modulator, it should not exceed 55000Kb/s, otherwise

overow occurs.

TS ID: You can congure the TS ID to mark the multiplexed TS. The default

value is 1.

Program List: Press the <ENTER>-key to enter ‘Mux List’ sub-menu. It shows

all programs detected by IDLV-4000P. The programs could be come from ASI

input, Tuner, TS/IP input or the internal CI de-encryption block. Use <↑> <↓>-keys

to roll up the program names, and use <←> <→>-keys to switch among input

sources, where the character in front of the program name indicates the input

source:

A-xxxxx: the program comes from the ASI input.

T-xxxxx: the program comes from the TUNER input.

I –xxxxx: the program comes from the TS/IP input

C-xxxxx: the program comes from the internal CI function block.

(xxxxx is the program name)

On ‘Mux List’ sub-menu, which is on the rst row, all encrypted programs are

labeled with a ‘$’ sign. All programs being selected to be re-multiplexed are

labeled as ‘Pass’, otherwise, the un-selected programs are labeled as ‘Fobrid’.

Use <ENTER>-key to selected or un-selected the program being shown.

When leaving the ‘Mux List’ sub-menu, a new menu will be shown ‘Conrm

changed?’ Press the <ENTER>-key to validate all programs just be selected to

be multiplexed or press the <EXIT>-key to discard the settings.

After a few seconds, the multiplexed TS will be generated and delivered to the

specied destination(s).

Filter function description

Filter Switch: The internal lter could be switched On/Off. The default value is

‘off’. To activate the lter function, you should turn on this lter functional block.

Bit Rate: Should be set to a specied value that does not exceed the Maximum

physical limit of the output medium, otherwise overow occurs.

Source: To select the signal source of lter function block, there are 4 type of

signal source optional: CI De-encrypted, TUNER,

ASI Input, and TS/IP input (only available when the TS/IP is set “IP In”.) Use

<ENTER>-key to save or press <EXIT>-key to discard.

Program List: Press the <ENTER>-key to enter ‘Filter List’ sub-menu. It shows

all programs carried by the signal come from the selected source in previous

step. The programs could be come from ASI input, Tuner, TS/IP input or the in-

ternal CI de-encryption block. Use <↑> <↓>-keys to roll up the program names,

where the character in front of the program name has the same meaning as

Mux function.

On ‘Filter List’ sub-menu, all programs that are being selected to be ltered

away are labeled as ‘Forbid’, otherwise, the un-selected programs are labeled

as ‘Pass’. Use the <ENTER>-key to selected or un-selected the program being

shown.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDLV-4000P in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inverto IDLV-4000P Manual

Product: