509835
17
Zoom out
Zoom in
Previous page
1/66
Next page
1EnIDL5000HD-print.fh10 1/18/06 12:53 PM Page 17
Composite
C M Y CM MY CY CMY K
6.6.3.8 Motor Settings
If you wish to connect the receiver to a rotating antenna (DiSEqC Level 1.2), call up the Main Menu, then
pressing Installation / Setup, then pressing “ Outdoor Settings”, then go to entry “ LNB Type” and use the
/ directional keys to select the setting “Motorized” for every LNB number, which has to be controlled by
the motor. Where you will find a facility for setting the position of the antenna manually for the various
satellite positions, and can then store these positions in memory. In the window “ Motor settings”, select
from the displayed list the satellite you want to reach with the next antenna position. The receiver at this
stage has already registered which transponders are available on this satellite, and will indicate the signal
strength and quality in the form of a bar graph. You can use this to find the optimum for the antenna.
In order to rotate the antenna towards the East or West, use the directional keys to select either “Move
coarse” or “More fine”. When the satellite position has been found, select “Save Position” in order to store
this permanently. In future, the receiver will automatically turn the antenna to this position whenever you
tune to a programmed slot available from this position.
Apart from storing all required satellite positions, you should also make a point of programming an easterly
and a westerly limit position for the motor. This is particularly important if other buildings or structures in
the vicinity restrict the rotation of the antenna. These could damage the antenna, motor or surrounding
objects if pre-programming does not restrict the limit of rotation.
6.6.4 Channel Search
New digital satellite TV and radio program are added almost on a
day daily basis, or existing program will change their frequency.
If you wish to receive these programs, you must allocate them to
specific program slots in the program list, and store them in memory.
The program search function is designed to assist you in this
activity, and there are various types of program search available.
Several procedures can be followed in order to initiate a program
search. Press the “Menu” key to call up the Main Menu, then using
the / directional keys select the sub-menu “Installation / Setup”,
followed by “Channel Search”, confirming your selection in each
case by pressing the “OK” key. Here you can decide between the
three options.
6.6.4.1 Quick Search
Use the automatic program search to allow your receiver to search
through an entire satellite position for new program. In this case,
the entire frequency range of the satellite is searched. The following
information must be input to the receiver:
Satellite: First select the satellite position to be searched. Below
this you will see a display of the current signal strength.
All newly found program would now be displayed on the following
page. At the end, the result of the program search will be displayed.
The search procedure can be terminated at any time by pressing
the “EXIT” key.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDL-5000HD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDL-5000HD in the language / languages: English as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info