Manual Inspire M2 (page 14 of 30) (English)

738440

Zoom out

Zoom in

1/30

Hex Head goes on side

with the stop flat.

Step 15: Insert L/E cable into hole at bottom of Floating

Pulley Bracket. Secure with Cable Adapter and Pulley 19.

Tighten Now. Tighten Step 13 Now.

Cable Adapter

STEP 14

1–M12 x 95 Hex Bolt

1 - M12 Flat Washer

1–M12 Thin Lock Nut

STEP 13

2–3 ½”Pulley

1–M10 x 115 Hex Bolt

2–M10 Flat Washers

1–M10 Lock Nut

STEP 15

1–3 ½”Pulley

1 - M10 x 45 Hex Bolt

2–M10 Flat Washers

1–M10 Lock Nut

Pulley 13

Pulley 12

Pulley 19

Pulley 3

Pulley 4

Pulley 2

Step 14 (Leg

Extension Cable)

Note: Be sure to feed the L/E

Cable between the 2 small

pulleys and over the small plate

behind the 2 small pulleys, as

the L/E and Cam are attached.

Step 13: Attach Pulleys 12 & 13 to Main Upright.

Step 14: Remove the 4 Flat Head Cap Screws

and Cam Plate from the L/E Cam. Next, using the

same 4 Flat Head Screws and the Cam Plate,

attach the Leg Extension Cable to the L/E Cam as

shown in the circle diagram. Tighten Now!

Attach L/E Cam and L/E Assembly to the front of

Main Base (Lower Numbers on Cam should be on

top). See Note! Tighten Now, Do Not Over

Tighten. L/E Assembly should swivel freely.

Route L/E cable behind Pulley 3, down to front of &

under Pulley 4 (make sure cable is routed between

the cable retainer pin and pulley on Pulleys 4 & 2),

back under & up around Pulley 2, to Floating

Pulley Bracket. Go to Step 15 above.

Pulley 19

PAGE 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inspire M2 in the language / languages: English as an attachment in your email.

The manual is 7,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inspire M2 Manual

Product: