Manual Ide line 17570002 (page 18 of 31) (English, German, Danish, Swedish, Norwegian, Finnish)

509039

Zoom out

Zoom in

1/31

KEY TO THE MAIN COMPONENTS OF THE

APPLIANCE

1. Temperature regulation button (thermostat)

2.Storagedrawers/shelves

3.Door

Settings

MIN (cold)

MED(colder,standardsetting)

MAX (coldest)

INSTALLATION

Each individual appliance is checked at the factory but, for

safety’ssake,afterunpacking,youshouldcheckcarefully

that the appliance has not been damaged during transport.

• Checkwhetherthereisanyvisibledamage(e.g.inthe

form of dents or similar), if the door (3) closes properly,

and if the hinges are in order.

• Iftheapplianceappearstohavebeendamaged,

contact the shop where you bought it, and do not use

it until it has been checked by an authorised specialist.

Installation place

For the appliance to function correctly, it should be

installed in a dry place, away from direct sunlight and at a

distance from sources of heat. The ambient temperature

mustbeat16ºC–32ºC.Donotusetheapplianceinan

unheated kitchen, a shed, a conservatory or a garage.

The appliance can be installed as a free-standing appliance

orinabuilt-incupboard.Underallcircumstances,itmust

beplacedadjacenttoawall.Theappliancemustbe

installedonaat,levelsurfacethatcansupporttheweight

of the appliance and its contents.

Installation:

1. Placetheapplianceinasuitablelocation,adjacentto

a wall. The ventilation panel at the rear of the appliance

should touch the wall.

o There must be clearance of at least 50 mm from

the top of the appliance and 25 mm to each side

oftheappliancetoensuresufcientventilation.

o Make certain that the appliance does not rest on

the cord.

o Parts that become hot must not be exposed.

2. Make sure that the appliance is level and that it cannot

tipforwards.Toadjustthepositionoftheappliance,

alignthescrewsonthefeetwithngersoraspanner.

o For best results, allow the appliance to tip slightly

backwards. This will ensure that the door cannot

open by itself.

3. After installation, allow the appliance to stand for 2

hours before switching it on, to allow the coolant to

settle.

NOTE!Takecarewhenmovingtheappliance.Itisvery

heavy.

PREPARING THE APPLIANCE

1. Beforeuse,checkthatyouhaveremovedalltransport

packaging inside and out.

2. Clean the appliance using warm water and a little

bicarbonate of soda (5 ml per ½ litre of water). Never

use soap or detergent as these can give off odours.

Never use detergents containing bleaching agent or

spirit. Allow the appliance to dry completely before

use.

CONNECTING THE APPLIANCE

1. After installation, allow the appliance to stand for 2

hours before switching it on, to allow the coolant to

settle.

2. Plug in and switch on the power.

3. Setthetemperatureregulationbutton(1)tothe

requiredsetting(seebelow:Settingthetemperature

regulation button).

4. Allowtheappliancetorunemptyforapproximately4

hoursuntilithasreachedatemperatureof-18ºC.

USING THE APPLIANCE

The appliance is intended for long-term storage of

frozen foods (up to 3 months or in accordance with

themanufacturer’sinstructions)andforfreezingfresh

food produce. The temperature inside the appliance is

controlled automatically by a thermostat that ensures a

constanttemperatureof-18ºC.Tocheckthetemperature

inside the appliance, place a thermometer between the

frozen food for a few minutes before reading the gauge.

Remove the thermometer from the appliance and read

the gauge immediately. The temperature reading will rise

rapidly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ide line 17570002 in the language / languages: English, German, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ide line 17570002 Manual

Product: