12680
43
Zoom out
Zoom in
Previous page
1/78
Next page
35
7
CALL PROCEDURE
7
2001 NEW
Position request call
The position request call is used to conrm the speci-
ed ships position. This calling system uses digital sig-
nals only, therefore a voice reply is not necessary.
q Push [MODE
SET
] to select the DSC menu.
w Rotate [CH] to select the Position REQ,
then push [ENT].
e Select the desired 9-digit ID code, then push
[ENT].
Use [CH] to select the ID code when the desired ships
ID is pre-programmed.
Select Manual set with [CH] then push [ENT],
after that, enter the desired 9-digit ID the via keypad.
r Rotate [CH] to select the desired pre-programmed
calling frequency, or Manual set then push
[ENT].
2177 kHz should be used for ship-to-ship calls.
When the pre-programmed traffic frequency is
selected, go to step y.
t Enter the desired transmit and receive call fre-
quency via the keypad, then push [ENT].
y The calling stand-by screen is displayed as fol-
lows, verify the calling condition then push and
hold [CANCEL/CALL] for 1 sec. to transmit the po-
sition request call.
Push and hold [ENT] for 1 sec. to store the calling con-
dition into the TX memory as described in pages 23
and 43, if desired.
u After sending the call, the transceiver waits for the
acknowledgement.
i When receiving the acknowledgement, the display
shows the ships position as follows.
NOTE:
The seconds digits may not be displayed ac-
cording to the called stations system.
o Push [ENT] to return to DSC watch mode.
When no acknowledgement is received:
q Wait for 5 min., then call again on the same or
a different frequency.
w If no acknowledgement is received after a 2nd
call, wait for at least 15 min. before repeating
the call.
************************
*
Position
ACK
*
*
IC-M802
*
*
Lat
35
35'N
*
*
Lon
135
35'W
*
************************
Exit
RX
J2B
GPS
<
Wait
for
ACK
>
Position
REQ
Lat
34
34'N
Lon135
34'E
12:34
SP
Exit
*****
Position
REQ
*****
---------
Call
---------
To:987654321
Call
Freq:TX
2345.0kHz
RX
2345.0kHz
Write-Menu
Call
*****
Position
REQ
*****
----
Call
frequency
----
TX:_2345.0kHz
RX:_2345.0kHz
OKSEL
*****
Position
REQ
*****
----
Call
frequency
----
Manual
set
T:
2345.0kHz
IC-M802-1
R:
2345.0kHz
T:
2177.0kHz
SHIP
R:
2177.0kHz
Ç
OKSEL
*****
Position
REQ
*****
------
Address
ID
------
987654321
OK
*****
Position
REQ
*****
------
Address
ID
------
Manual
set
IC-M802-1
123456789
IC-M802-2
123456788
IC-M802-3
123456787
IC-M802-4
123456786
IC-M802-5
123456785
Ç
OKSEL
IC-M802_USA.qxd 02.7.9 10:58 Page 35
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-M802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-M802 in the language / languages: English as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info