670411

Icom IC-FR9010 Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
4
8.2 CALL ALERT
To send a Call Alert, push [F] then push [A] or [B]
until the selection is displayed, then enter the tar-
get ID of the radio to alert and push [#]. If the target
radio has received the Call Alert the display should
show “ACK” (acknowledgement).
Figure 12 displays a Call Alert ACK.
Figure 12
8.3 RADIO CHECK
The dispatcher can send a message to a subscrib-
er unit requesting a response from the radio. (For
example, to check if it is in operation.)
To initiate a Radio Check, push [F] then push [A]
or [B] until the selection is displayed, then enter
the target ID of the radio to alert and push [#]. If the
target radio has received the Call Alert the display
should show “ACK” (acknowledgement).
Figure 13 shows Radio Check display.
Figure 13
8.4 RADIO INHIBIT
This function is used to disable a subscriber unit
(mobile or portable). The subscriber unit cannot
be turned ON at all until an Uninhibit Command
is sent. The password must match the password
entered in the BTIII program for inhibit to occur.
To inhibit a radio, push [F] then push [A] or [B] un-
til the selection is displayed then enter the target
radio’s ID. Push [D] and enter the programmed
password, then push [#]. The target radio will be
totally disabled. If the target radio has received
the Call Alert the display should show “ACK” (ac-
knowledgement).
Figure 14 shows the Radio Inhibit entry display.
Figure 14
8.5 RADIO UNINHIBIT
Used to enable a subscriber unit that has been
disabled, the password must match the password
entered in the BTIII program.
To uninhibit a radio, push [F] then push [A] or [B]
until the selection is displayed and enter the target
radio’s ID, enter the password and then push [#].
The target radio will be returned to normal opera-
tion. The target radio should send an ACK if suc-
cessful.
Figure 15 shows the Radio Uninhibit entry mode.
Figure 15
8.6 STATUS UPDATE
Used to send user status. The status numbers re-
lates to an actual message list. Indicates the User
status (0–255) and Unit status (0–255).
To send a Status Update, push [F] then push [A]
or [B] until the selection is displayed and enter the
target radio ID. Then push [D] and enter the user
(USR), message number, push [D] again and en-
ter the unit number, then push [#]. If the target ra-
dio has received the Call Alert the display should
show “ACK” (acknowledgement).
Figure 16 shows Status Update ready to be sent
to 366.
Figure 16
8.7 STATUS REQUEST
Used to request the status of another unit. After
the request is sent the target unit should respond
with the current status. In the example below USR:
2 means the number 2 status message.
To send a Status Request, push [F] then push [A]
or [B] until the selection is displayed and enter the
target radio ID then push [#]. The target unit should
respond with the message number, unit ID and
ACK.
Figure 17 shows Status Request received from
366.
Figure 17
Call Alert
To: 366
MD N
Fm: 00000366 (ACK)
Radio Check
To: _
MD N
Fm: 00000366 (ACK)
Radio Inhibit
To: _
Password: MD N
Radio Uninhibit
To: _
Password: MD N
Status Update
To: 366
USR: 1 UNT: 0 MD N
Status Request
To: 366
USR: 2 UNT: 0 MD N
FM: 00000366 (ACK)
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-FR9010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-FR9010 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info