670155
17
Zoom out
Zoom in
Previous page
1/232
Next page
1-7
MF5 (MULTI-FUNCTION 5 SWITCH)
➥ Activates and selects a fast, mid
or slow AGC time constant when
pushed. (p. 5-12)
•IntheFMmode,only“FAST”isavailable.
➥ Selects the AGC set mode when held
down for 1 second. (p. 5-12)
The AGC time constant can be set be-
tween 0.1 and 8.0 seconds (depending
on the mode), or turned OFF. When the
AGC is “OFF, the S-meter does not
function.
What is the AGC?
The AGC controls the receiver gain to produce a con-
stant audio output level, even when the received signal
strength varies dramatically. Select “FAST” for tuning and
then select “MID” or “SLOW, depending on the receiving
condition.
MF6 (MULTI-FUNCTION 6 SWITCH)
➥ Turns the speech compressor ON or
OFF in the SSB mode. (p. 6-5)
➥ Switches the compression between
narrow, mid or wide when held down
for 1 second.
What is the speech compressor?
The speech compressor compresses the transmitter
audio input to increase the average audio output level,
to increase talk power. This function is effective for long-
distance communication or when propagation conditions
are poor.
➥ Turns the 14-speed tuning function
ON or OFF in the SSB data, CW,
RTTY and PSK modes. (p. 3-6)
•
14 function sets dial rotation to 14 of
normal speed for fine tuning.
➥ Switches between the tone encoder,
tone squelch function and no-tone op-
eration when pushed in the FM mode.
(pp. 4-33, 4-34)
➥ Selects the tone set mode when held
down for 1 second in the FM mode.
(pp. 4-33, 4-34)
MF7 (MULTI-FUNCTION 7 SWITCH)
➥ Switches the voice squelch control
function ON or OFF; useful for scan-
ning. (p. 9-3)
#4 LCD FUNCTION SWITCHES F-1 F-7
Push to select the function indicated in the LCD
display above these switches.
•Functionsvary,dependingontheoperatingcondition.
#5 TRANSMIT INDICATOR [TX]
Lights red while transmitting.
#6 RECEIVE INDICATOR [RX]
Lights green while receiving a signal and when the
squelch is open.
#7 LCD FUNCTION DISPLAY (p. 1-14)
Shows the operating frequency, function switch
menus, spectrum scope screen, memory list
screen, set mode settings, etc.
#8 SPLIT OPERATION INDICATOR [SPLIT]
Lights during split frequency operation.
#9 LOCK INDICATOR [LOCK] (p. 5-18)
Lights when the dial lock function is activated.
$0 TRANSMIT FREQUENCY CHECK SWITCH
[XFC] (p. 6-6)
Monitors the transmit frequency (including TX
frequency offset) when held down during split fre-
quency operation.
•Whilepushingthisswitch,thetransmitfrequencycan
be changed with the main dial, keypad, memo pad or
/ switches.
•WhenthesplitlockfunctionisturnedON,pushing
[XFC] cancels the dial lock function. (p. 6-7)
$1 MEMORY UP/DOWN SWITCHES /
(p. 8-2)
Push to select the desired memory channel.
MemorychannelscanbeselectedbothinVFOand
memory modes.
$2 KEYPAD
Pushing a key selects the operating band.
(p. 3-4)
•
GENE selects the general coverage band.
Pushing the same key 2 or 3 times calls up
other stacked frequencies in the band. (p. 3-4)
•Icom’striplebandstackingregistermemorizes3fre-
quencies in each band.
After pushing F-INP
ENT , enters a frequency or
memory channel. Pushing F-INP
ENT or /
is necessary to end the entry. (pp. 3-5,
8-2)
•Toenter14.195MHz,push F-INP
ENT 1.8 1 10 4
GENE 1.8 1 28 9 14 5 F-INP
ENT .
VSC
OFF
TONE
OFF
1
/
4
ON
COMP
OFF
WIDE
AGC
MID
1
PANEL DESCRIPTION
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7700 in the language / languages: English as an attachment in your email.

The manual is 23,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info