670163

Icom IC-7300 Manual

160
Zoom out
Zoom in
Previous page
1/173
Next page
19
CONTROL COMMAND
19-7
Remote control (CI-V) information (Continued)
Cmd. Sub cmd. Data Description
1C 00* 00 Send/read transceiver’s status RX
• When CI-V Output (for ANT) (Command:
1A 05 0157) is set to ON, automatically
outputs when changed.
01 Send/read transceiver’s status TX
• When CI-V Output (for ANT) (Command:
1A 05 0157) is set to ON, automatically
outputs when changed.
01* 00 to 02 00=Send/read the antenna tuner OFF
01=Send/read the antenna tuner ON
02=Send/read to tuning
02* 00/01 Send/read transmit frequency monitor setting
(00=OFF, 01=ON)
03 p. 19-8 Read transmit frequency
• When CI-V Output (for ANT) (Command:
1A 05 0157) is set to ON, automatically
outputs when changed.
04* 00/01 Send/read command to disable to output the
antenna controller status frequency and so on
from [REMOTE]
• Send/read command to enable to output the
antenna controller status frequency and so
on from [REMOTE].
1E 00 Read number of available TX frequency band
01 p. 19-8 Read TX band edge frequencies
02 Read number of user-set TX frequency band
03* p. 19-8
Send/read user-set TX band edge frequencies
21* 00 p. 19-11 Send/read RIT frequency
01 00/01 Send/read RIT setting (00=OFF, 01=ON)
02 00/01
Send/read ∂TX setting (00=OFF, 01=ON)
25* p. 19-11 Send/read the selected or unselected VFO
frequency
26* p. 19-11 Send/read the selected or unselected VFO’s
operating mode and lter
27* 00 p. 19-12 Read the Scope waveform data
• Only when “Scope ON/OFF status”
(Command: 27 10) and “Scope data output”
(Command: 27 20) are set to “ON,” outputs
the waveform data to the controller.
10 00/01 Send/read the Scope ON/OFF status
(00=OFF, 01=ON)
11 00/01 Send/read the Scope wave data output*4
(00=OFF, 01=ON)
12 00 Send/read the Main or Sub scope setting
(00=Main only)
13 00 Send/read the Single/Dual scope setting
(00=Single only)
14 p. 19-12 Send/read the Scope Center mode or Fixed
mode setting
15 p. 19-12 Send/read the span setting in the Center
mode Scope
16 p. 19-12 Send/read the Edge number setting in the
Fixed mode Scope
17 p. 19-12
Send/read the Scope hold function ON or OFF
19 p. 19-12 Send/read the Scope Reference level setting
1A p. 19-13 Send/read the Sweep speed setting
1B 00/01 Send/read the Scope indication during TX in
the Center mode (00=OFF, 01=ON)
1C 00 to 02 Send/read scope center frequency setting in
the Center mode
( 00=Filter center, 01=Carrier point center,
02=Carrier point center (Abs. Freq.)
1D p. 19-13 Send/read the Scope VBW setting
1E p. 19-13 Send/read the Scope Fixed edge frequencies
D Command table (Continued)
* (Asterisk) Send/read data
*1 To insert a counter, rst clear the other channel’s counter.
*2 In the CW mode, if the [TRANSMIT] or an external TX
switch is ON, or the Break-in function is ON, a message
will be transmitted as CW code when you send it from
your PC.
*3 When sending the power ON command (18 01), you need
to repeatedly send “FE” before the standard format. The
following is the approximated quantity of the repetition.
• 115200 bps: 150 “FE”s
• 57600 bps: 75 “FE”s
• 38400 bps: 50 “FE”s
• 19200 bps: 25 “FE”s
• 9600 bps: 13 “FE”s
• 4800 bps: 7 “FE”s
Example: When using 4800 bps
F
F E
x7
49EFE E 1081O DF
*4 You can only set this item when “Unlink from [REMOTE]”
is selected on the “CI-V USB port” screen, and then
“115200” is selected on the “CI-V Baud Rate” screen.
… 160 …


Need help? Post your question in this forum.

Forumrules
1

Forum

icom-ic-7300

Reset search

  • is there available a wiring pictorial chart for the small internal ic-7300 coaxial jumper cables?
    ie: from the RF unit to the PA board? tnx Sam in Alabam KF4TXQ Submitted on 2-1-2022 at 06:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7300 in the language / languages: English as an attachment in your email.

The manual is 24,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info