670164
91
Zoom out
Zoom in
Previous page
1/104
Next page
PROBLEM POSSIBLE CASE SOLUTION REF.
TRANSMIT
Transmitting is impos-
sible.
T
he operating frequency is not set in a
ham band.
• Set the frequency in a ham band. p. 25
Output power is too
low.
Power is set to a lower power than max-
imum.
• Set the output power in quick set mode. p. 71
• Microphone gain is set too low.
Set microphone gain to a suitable level
in quick set mode.
p. 71
The antenna is not connected properly. • Reconnect the antenna connector.
The antenna feed line is cut or shorted.
Check the feed line and correct any im-
proper conditions.
The antenna is not properly tuned.
Push
TUNER
to manually tune the an-
tenna or test with dummy load.
p. 67
T
he antenna for another band is se-
lected.
Select an antenna suitable for the oper-
ating frequency.
p. 67
No contact possible
with other stations.
• RIT function is activated.
Push
RIT
to turn the function OFF.
p. 44
• Split function is activated.
Push
SPLIT
to turn the function OFF.
p. 58
Transmitted signals are
distorted.
• Microphone gain is set too high.
Set microphone gain to a suitable level
in quick set mode.
p. 71
The compression level is set too high
with the speech compressor ON.
Set compression level to a suitable po-
sition.
p. 57
DISPLAY
Displayed frequency
does not change prop-
erly.
The dial lock function is activated.
Push and hold
SPCH
for 1 sec. to deacti-
vate the function.
p. 29
The internal CPU has malfunctioned. • Reset the CPU. pgs. 21,
84
SCAN
Pr ogram med sc an
does not stop.
[RF/SQL] is assigned to RF gain control
and squelch is open.
Reset [RF/SQL] control assignment and
set it to the threshold point.
p. 30
Pr ogram med sc an
does not start.
T
he same frequencies have been pro-
grammed in scan edge memory chan-
nels.
Program different frequencies into scan
edge memory channels.
p. 62
Memory scan does not
start.
2 or more memory channels have not
been programmed.
• Program 2 or more memory channels. p. 62
MEMORY
The memory channels
cannot be selected
with rotating the [M-CH]
control.
The
[M-CH] control acts as the RIT con-
trol mode.
Push
M-CH/RIT
SET
to set the [M-CH] con-
trol to memory channel control. (RIT
control indicator goes out).
p. 61
86
12
TROUBLESHOOTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7200 in the language / languages: English as an attachment in your email.

The manual is 10,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info