670168
88
Zoom out
Zoom in
Previous page
1/96
Next page
6
SET MODE
6-6
PTT Start OFF or ON Turns the PTT Tuner Start function ON or OFF.
[TUNER] Switch Manual or Auto Selects whether or not to store the AT-180’s sta-
tus by each band.
[SPEECH/LOCK] Switch SPEECH/LOCK, LOCK/SPEECH
Selects the function for
SPEECH
when pushed
or held down.
Lock Function MAIN DIAL or PANEL Select the target to be locked when the Lock
function is activated.
Memopad Numbers 5 or 10 Sets the number of usable memopad channels.
MAIN DIAL Auto TS OFF, LOW or HIGH Selects an option for the automatic tuning step
function. When rapidly rotating the main dial, the
tuning step automatically changes according to
the setting.
MIC Up/Down Speed Slow or Fast Selects the microphone’s []/[] key speed.
[NOTCH] Switch (SSB) Auto, Manual or Auto/Manual Selects the notch function for the SSB mode.
[NOTCH] Switch (AM) Auto, Manual or Auto/Manual Selects the notch function for the AM mode.
SSB/CW Sync Tuning OFF or ON Turns the Synchronous Tuning function ON or
OFF to shift the operating frequency by the offset
amount to keep receiving a signal when the oper-
ating mode is changed between SSB and CW.
CW Normal Side LSB or USB Sets the carrier point for CW normal mode op-
eration to the LSB side or the USB side.
VOICE 1st Menu VOICE-Root or VOICE-TX Select whether or not to directly select the “VOICE
TX” screen, skipping the “VOICE” screen.
KEYER 1st Menu KEYER-Root or KEYER-SEND Select whether or not to directly select the
“KEYER SEND” screen, skipping the “KEYER”
screen.
Speaker Out OFF or ON Selects to mute the speaker output.
MIC AF Out OFF or ON Selects to output the received audio from the
[MIC] connector.
RC MIC
[F-1] ---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK, SPLIT, A/B, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO (DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-1]
of the optional HM-151
r e m o t e c o n t r o l m i c .
[F-2] ---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK, SPLIT, A/B, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO (DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-2]
of the optional HM-151
r e m o t e c o n t r o l m i c .
Mode Select
SSB, CW, RTTY, AM, FM,
WFM, DV
(All boxes are checked.)
Disables the mode selection of the optional HM-
151
r e m o t e c o n t r o l m i c , to simplify operation.
Power OFF (With No Controller) OFF or ON Selects whether or not to automatically turn OFF
the transceiver when the controller is disconnect-
ed from the transceiver.
REF Adjust 0%~100% Sets a number to adjust for a zero beat with a
standard signal such as WWV or WWVH, for fre-
quency calibration.
Set mode items and Default settings (Continued)
NOTE: The default settings shown below in bold are for the USA version.
The default settings may differ, depending on your transceiver version.
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7100 in the language / languages: English as an attachment in your email.

The manual is 25,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info