670168
7
Zoom out
Zoom in
Previous page
1/96
Next page
1
PANEL DESCRIPTION
1-3
e TX/RX LED
Lights green when the squelch opens, or a signal
is received.
Lights red when transmitting.
r MEMORY BANK CONTROL [BANK]
❍ When both the PBT and RIT LEDs are OFF
Rotate to select a Memory bank.
❍ When the PBT LED (y) lights green
(Mode: SSB/CW/RTTY/AM)
Rotate to adjust the receiver’s IF filter passband
width using the DSP circuit.
❍ When the RIT LED (u) lights orange
Disable this control.
t
M-CH CONTROL•CLEAR SWITCH [M-CH]•[CLR]
Push to select the action of the [M-CH/BANK] con-
trols as the Memory/Bank selection, PBT control or
RIT control.
❍ When the both RIT and PBT LEDs are OFF
Rotate to select a Memory channel.
❍ When the RIT LED lights orange
Rotate to adjust the RIT frequency shift.
  •The frequency shift rangeis ±9.99 kHz in 10 Hz
steps. The control tunes in 1 Hz steps when the op-
erating frequency readout is set to the 1 Hz step.
Hold down for 1 second to clear the RIT shift
frequency.
What is the RIT function?
The RIT (Receiver Incremental Tuning) shifts the re-
ceive frequency without shifting the transmit frequency.
This is useful for fine tuning stations calling you off-fre-
quency, or when you prefer to listen to slightly different-
sounding voice characteristics.
❍ When the PBT LED lights green
(Mode: SSB/CW/RTTY/AM)
Rotate to adjust the receiver’s IF filter pass-
band width using the DSP circuit.
➥
Hold down for 1 second to reset the PBT set-
tings.
  •ThePBTisadjustablein50HzstepsintheSSB/
CW/RTTY modes, and 200 Hz in the AM mode. At
that time, the shift value changes in 25 Hz steps in
the SSB/CW/RTTY modes, and 100 Hz in the AM
mode.
  •ThePBTcontrolsfunctionasanIFshiftcontrol.
What is the PBT control?
The PBT function electronically modifies the IF pass-
band width to reject interference. This transceiver uses
the DSP circuit for the PBT function.
y PBT LED
Lights green when the [M-CH/BANK] controls act
as the PBT control.
 •Pushthe[M-CH] switch to select PBT control.
u RIT LED
Lights orange when the RIT function is turned ON.
Lights orange when the [M-CH/BANK] controls
act as the RIT control.
  •Pushthe[M-CH] switch to select RIT control.
  •The RIT control is the inner control. The outer control
is disabled.
i RIT KEY
RIT
(AI sec. 5)
Push to turn the RIT function ON or OFF.
  •Usethe[M-CH] control to vary the RIT frequency.
Hold down for 1 second to add the shift frequency
of the RIT function to, or subtract it from, the dis-
played frequency.
o ANTENNA TUNER/CALL KEY
ANTENNA TUNER KEY Operation (AI sec. 16)
(Frequency band: HF/50 MHz)
Push to turn an optional automatic antenna
tuner ON or OFF (bypass).
Hold down for 1 second to manually tune the
antenna tuner.
  •Ifthetunercannottunetheantennawithin20sec-
onds, the tuning circuit is automatically bypassed.
CALL KEY Operation (AI sec. 11)
(Frequency band: 144/430 MHz)
Push to select the Call channel.
In the 70 MHz band, push to sound an error beep.
!0 MENU KEY
MENU
(p. 1-10)
Push to change the set of functions assigned to the
touch keys.
 •TogglesthefunctiondisplaymenubetweenM-1,M-2and
M-3 menus or D-1 and D-2 menus.
!1 MIC GAIN/RF POWER ADJUSTMENT KEY
MIC/RF PWR
(p. 3-24)
Push to open the MIC gain/RF power adjustment
display.
 •Rotate[M-CH] to adjust the MIC gain.
 •Rotate[BANK]
to adjust the RF power.
Frequency band RF output power range
HF/50 MHz 2 to 100 W (AM: 1 to 30 W)
70 MHz* 2 to 50 W (AM: 1 to 15 W)
144 MHz 2 to 50 W
430 MHz 2 to 35 W
 •Pushagaintoclosethewindow.
* 70 MHz band transmission is available, depending on the
transceiver version.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Icom IC-7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Icom IC-7100 in the language / languages: English as an attachment in your email.

The manual is 25,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info