571938
9
Zoom out
Zoom in
Previous page
1/20
Next page
Page 9 of 20 pages
3. Remove the front of the heat storage compartment (8). Loosen the two screws (9) on each side of
the front of the heat storage compartment without removing them. Then pull the front forward.
4. Removing the heat shield (7). Uninstall the heat shield on the outside of the rear plate by removing the
three screws. The heat shield has a cut-out for the flue duct. Break off the pre-cut plate; the resulting
hole fits the flue duct.
5. Removing the rear plate (2). Lift the rear plate and pull it away from the stove so that it disengages
from the guide pins on the bottom plate of the stove. There is a cut-out in the rear plate for the smoke
outlet. Break off the plate within this cut-out to make a hole in the rear plate so there is room for the
smoke outlet.
6. Removing the cover plate (3). Remove the cover plate on the back of the stove by removing the three
screws (Torx Bit no. 30).
7. Open the metallic tabs (5) and take the wires out.
8. Pull the lambda sensor coupling (10) free of the wire fastener (11).
9. Remove the temperature monitor from the smoke ring.
10. Remove the flue ring (4) and fasten it to the rear of the stove. NB: Remember to turn the lambda
probe (6) as illustrated in drawing D1.
11. Reattach the temperature monitor in the smoke ring, leading the sensor about 3 cm into the smoke
ring.
12. Reposition the lambda sensor coupling (10) in the wire fastener (11).
13. Fix the two wires by closing the metallic tabs (5) again.
14. Installing the rear plate (2). Place the rear plate on the guide pins at the back of the bottom plate of
the stove; then press it in towards the stove. Lift the rear plate and press it lightly inwards until it
engages with the guide pins.
15. Installing a heat shield (7). Replace the heat shield at the back of the stove.
16. Installing the front on the heat storage compartment (8). Place the front on the heat storage compart-
ment and fasten with the four screws (9).
17. Installing the top plate of the stove (1). Place the top plate on the fittings and secure it with the four
screws, two on each side.
18. Installing sides. Put the sides on the guide pins in the bottom plate of the stove and press them in towards
the stove. Lift the sides and press them lightly inwards until they engage with the guide pins.
An accessory top cover is available to cover the hole in the stove top plate if the smoke outlet is con-
nected at the rear of the stove.
Connection to chimney
All the stoves have both back and top smoke outlet that can be connected to an approved steel chimney on
top or directly out at the back to a chimney.
Make sure that the chimney is tight and that no false draft is caused around neither the cover plate, in
connection with a covered smoke outlet, nor the cleanout door and pipe connections. Please note that
bent and/or horizontal smoke pipes will reduce the effect of the chimney draft.
Vertical cross-section of smoke flue (Drawing B and C)
B: Top outlet
C: Back outlet
Steel chimney (9).
Flue gas elbow (10). Fits into smoke flue socket.
Brick-built jamb of flue (11).
Built-in pipe sleeve (12). Fits smoke flue.
Wall rosette (13). Covers disruption to wall around pipe sleeve.
Joint (14). Sealed with packing material.
Smoke outlets (15) of the HWAM stove.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hwam 3520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hwam 3520 in the language / languages: English as an attachment in your email.

The manual is 1.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hwam 3520

Hwam 3520 User Manual - English - 56 pages

Hwam 3520 User Manual - German - 44 pages

Hwam 3520 User Manual - Dutch - 32 pages

Hwam 3520 User Manual - Danish - 56 pages

Hwam 3520 User Manual - French - 32 pages

Hwam 3520 User Manual - Italian - 44 pages

Hwam 3520 User Manual - Swedish - 56 pages

Hwam 3520 User Manual - Spanish - 44 pages

Hwam 3520 User Manual - Norwegian - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info