627067
18
Zoom out
Zoom in
Previous page
1/32
Next page
18
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
7.5. replacinG chanGe wheels
Disconnect the machine from the power source.
Loosen the 2 fastening screws and remove the cover.
Loosen the fastening screw (C, fig 21) on the quadrant.
Swing the quadrant (D) to the right.
Loosen the bolt (E) of the lead screw or loosen the bolts of the quadrant to remove the change wheels from the
front.
Install the change wheels according to the feed and threadcutting table (fig. 22) and mount them on the
quadrant.
Swing the quadrant to the left until the gear wheels engage.
Adjust the backlash by inserting a normal sheet of paper between the change wheels.
Tighten the fastening screw on the quadrant.
Reinstall the cover and tighten the screws. Connect the machine to the power source.
8. UsinG The Machine
8.1. sTraiGhT TUrninG
Figure 23 – Straight turning
With straight turning, the tool feeds parallel to the axis of rotation of the work piece. The feed can be either manual
or turning the hand wheel on the lathe saddle or the sop slide, or by activating the automatic feed. The cross feed for
the depth cut is achieved by using the cross slide.
8.2. facinG and recesses
Figure 24 – Facing and recesses
In the facing operation, the tool feed perpendicular to the axis of rotation of the work piece. The feed is made
manually with the cross slide hand wheel. The cross feed for cut depth is made with the top slide or lathe saddle.
8.3. TUrninG beTween The cenTers
Figure 25 – Turning between the centers
For turning between the centers, it is necessary to remove the jaw chuck. Fit the MT3 center into the spindle nose
and the MT2 center into the tailstock. Mount the work piece fitted with the driver dog between the centers. The
driver is driven by a catch or face plate.
Note!
Always use a small amount of grease on the tailstock center to prevent overheating.
8.4. Taper TUrninG UsinG TailsTock off-seT
Work pieces to a side angle of 5 mm can be turned by off-setting the tailstock. The angle depends on the length of
the work piece.
Proceed as follows to off-set the tailstock:
Loosen the fastening screw (A, fig. 26).
Loosen the fastening screw (B).
Loosen the front set screw (C) a couple of turns and tighten the rear set screw (D) the same amount of turns.
Repeat this until the required angle is reached. The value can be read on the scale.
Tighten the set screw (B) and the front (C) and rear (D) set screws to secure the tailstock in this position.
Tighten the set screw (A).
The work pieces must be held between the centers and drive by a face plate and driver dog.
After taper turning, return the tailstock to its original postion as indicated on the scale (E) of the tailstock.
8.5. Taper TUrninG by seTTinG The Top slide
Figure 27 – Taper turning by setting the top slide
By angling the top slide, tapers may be turned manually with the top slide. Rotate the top slide to the required angle.
A graduated scale permits accurate adjustment of the top slide. The cross feed is performed with the cross slide. This
method can only be used for short tapers.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 550 VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 550 VARIO in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 550 VARIO

Huvema HU 550 VARIO User Manual - German - 32 pages

Huvema HU 550 VARIO User Manual - Dutch - 32 pages

Huvema HU 550 VARIO User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info