627067

Huvema HU 550 VARIO Manual

16
Zoom out
Zoom in
Previous page
1/32
Next page
16
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
5.3. Gear box
Figure 4 – Gear box
The gear box is mounted on the left side of the bed. The knobs on the gear box are used, to select the feed for
turning and thread cutting.
5.4. carriaGe
Figure 5 – Carriage
The slide parts of the carriage are smoothly ground. They fit the V on the bed without play. De cross slide is mounted
on the carriage and moves on a dove tailed slide. Play in the cross slide may be adjusted with gibs. The cross slide is
moved by turning the hand wheel, which has been fitted with a graduated collar.
The top slide is mounted on the cross slide and can be rotated 360º. The top slide and cross slide travel move over
dove tail guides and have gibs and graduated collars. A four way tool post is fitted on the top slide and allows four
tools to be clamped. Loosen the center clamp handle to rotate any of the four tools into position.
5.5. apron
Figure 6 – Apron
The apron is mounted on the carriage. It houses the half nut with an engaging lever for activating the automatic
feed. The half nut gibs can be adjusted from the outside. The movement of the apron is transmitted by a rack and a
pinion that are mounted on the bed.
5.6. lead screw
Figure 7 – Lead screw
The lead screw is mounted on the front of the bed. It is connected to the gear box at the left for automatic feed and
is supported by bearing on both ends. Two groove nuts (A) on the right take up play on the lead screw.
5.7. TailsTock
Figure 8 – Tailstock
The tailstock slides on a V-way and can be clamped at any location. The tailstock has a sturdy MT2-spindle with a
graduated scale (in mm). The spindle can be clamped at any location with a clamping lever. It is moved by means of
the hand wheel on the tailstock.
Note!
Fit the securing screw (B, fig. 7) always at the end on the right of the machine. This will prevent the
tailstock of falling of the bed.
6. conTrol eleMenTs
A. Emergency switch + On/off switch (fig. 9): The machine is switched On and Off with the On/Off switch. This
switch can be found underneath the cover of the Emergency switch. Only push the Emergency switch when an
emergency occurs, all machine functions will be stopped. To restart after an emergency, lift the cover and press
the ON button.
B. Switch for changing spindle rotation (fig. 9): After the machine is switched on, turn the switch to the “F”
position for counter-clockwise spindle rotation (Forward). Turn the switch to “R” (Reverse) to make the spindle
turn to the right. Position “0” means OFF, the spindle remains idle.
C. Variable speed control switch (fig. 9): Turn the switch clockwise to increase the spindle speed, turn to the left
to decrease the spindle speed. The speed range depends on the position of the V-belt.
D. Feed direction selector (fig. 10): Select the carriage travel direction, it depends on the rotating direction of
the jaw chuck.
E. Feed rate selector (fig. 10): Use this switch to select the feed for threadcutting.
F. Lock (fig. 11): Turn the nuts clockwise to lock, counter-clockwise to release.
G. Compound slide lock (fig. 11): Turn the nuts clockwise to lock, turn counter-clockwise to release.
H. Cross slide lock (fig. 11): Turn the screw clockwise and tighten to lock. Loosen the screw and turn it counter-
clockwise to release.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 550 VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 550 VARIO in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 550 VARIO

Huvema HU 550 VARIO User Manual - German - 32 pages

Huvema HU 550 VARIO User Manual - Dutch - 32 pages

Huvema HU 550 VARIO User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info