627067
15
Zoom out
Zoom in
Previous page
1/32
Next page
15
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
2. characTerisTics and applicaTions
Swing over bed 250 mm
Swing over support 150 mm
Distance between centers 550 mm
Width of bed 135 mm
Hole through spindle 26 mm
Taper of spindle internal MT4
Spindle speeds variable
Spindle speed range 50-2500 RPM
Threadcutting (Metric) number 18
Threadcutting (Metric) 0.2~3.5 mm
Threadcutting (Whit) number 21
Threadcutting (Whit) 8~56 T.P.I.
Longitudinal feed range 0.07~0.20 mm
Tool holder 4-way
Top slide travel 70 mm
Cross slide travel 115 mm
Slide travel 480 mm
Tailstock spindle travel 70 mm
Tailstock spindle taper MT2
Motor power 0.75 kW
Dimensions 1150x560x570 mm
Weight 120 kg
Subject to change.
3. insTrUcTions for UsinG This Machine
Read the safety rules carefully and always observe them. Examine the applications of this machine and beware of
possible risks.
Always wear safety glasses.
4. UnpackinG
Figure 1 – Foundation scheme
Remove the wooden crate.
Check the machine for damage
Unbolt the lathe from the shipping crate bottom.
Place the machine in a dry, well-lit environment. Leave enough working space around the machine.
Use adequate lifting equipment to hoist the machine onto its location. Do no lift the machine at the spindle.
The foot of the machine has four holes, used to mount the machine on a sturdy bench or stand. The lathe must
be absolutely level before the bolts are tightened.
Clean all rust protected surfaces using a mild commercial solvent, kerosene or diesel fuel. Do not use paint
thinner, gasoline or lacquer thinner. This will damage painted surfaces. Cover all cleaned surfaces with a light
film of machine oil.
Remove the gear box cover. Clean all components and grease the gears. Install the cover again.
5. Machine parTs
5.1. bed
Figure 2 – Bed
By combining high cheeks with strong cross ribs, a bed of low vibration and rigidity is produced. The two V-sideways,
hardened and ground, are the accurate guide for the carriage and tailstock. The main motor is mounted at the rear
side of the bed.
5.2. headsTock
Figure 3 – Headstock
The headstock is bolted to the bed. The headstock houses the main spindle with two precision taper roller bearings
and the drive unit.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 550 VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 550 VARIO in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 550 VARIO

Huvema HU 550 VARIO User Manual - German - 32 pages

Huvema HU 550 VARIO User Manual - Dutch - 32 pages

Huvema HU 550 VARIO User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info