627067

Huvema HU 550 VARIO Manual

19
Zoom out
Zoom in
Previous page
1/32
Next page
19
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
8.6. Thread cUTTinG
Figure 28 – Thread cutting
Set the machine to the desired thread pitch. Switch the machine on and close the half nut. When the tool reaches the
work piece, it will cut the initial threading pass. When the tool reaches the end of the cut, switch the machine off and
at the same time move the tool out of the cut. Do not open the half nut! Reverse the motor direction to make the
tool return to the starting point. Repeat these steps until the desired result is obtained.
Advice for thread cutting
• The work piece diameter must compare to the diameter of the required thread.
• The work piece requires a chamfer of 45º at the beginning of the thread and an undercut at the thread run out.
• Speed must be as low as possible.
• Use the right combination of change wheels and adjustments to obtain the required thread pitch.
• The thread cutting tool must be exactly the same shape as the thread, must be rectangular and clamped so that
it coincides exactly with the turning center.
• The thread is cut in steps so that the cutting tool has to be turned out of the thread completely (with the cross
slide) at the end of each cutting step.
• The tool is withdrawn with the half nut engaged by using the on/off switch.
• Switch the machine off. Feed the thread cutting tool in low cut depths using the cross slide.
• Before each passage, place the top slide approximately 0.02 to 0.03 mm to the left and right alternately in order
to cut the thread free. This way, the thread cutting tools cut only one thread flank with each passage. Keep
cutting the thread free until you have almost reached the full depth of thread.
9. accessories
9.1. 3-jaw chUck
This 3-jaw chuck can be used to clamp round, triangular, square, hexagonal. octagonal and twelve-cornered work
pieces.
Note!
New 3-jaw chucks have very tight fitting jaws. This is necessary to ensure accurate clamping
and long service life. With repeated opening and closing, the jaw adjust automatically and their
operation becomes smoother.
Note
The original 3-jaw chuck has been mounted with tow “0” marks (A, fig. 29) on the chuck and chuck
flange.
There are two types of jaws: internal and external jaws. Please note that the number of jaws matches the number
inside the chuck’s groove. When you are going to mount them, please mount them in the ascending order 1-2-3 (as
indicated on the jaws), dismounting takes place in the reverse order 3-2-1. After you have finished the procedure,
rotate the jaws to the smallest diameter and check that the three jaws are well fitted.
9.2. independenT 4-jaw chUck
This chuck has 4 independently adjustable jaws (fig. 30). These permit the holding of asymmetrical or cylindrical
pieces.
9.3. drill chUck (opTional)
Use the drill chuck to hold centering drills and twist drills in the tailstock (A, fig. 31).
9.4. arbor (opTional)
An arbor is necessary for mounting the drill chuck in the tailstock. It has a MT2 taper (B, fig. 31).
9.5. sTeady cenTer (opTional)
The steady center is mounted in ball bearings. Its use is highly recommended for turning at speeds in excess of 600
RPM (fig. 32).
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 550 VARIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 550 VARIO in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 550 VARIO

Huvema HU 550 VARIO User Manual - German - 32 pages

Huvema HU 550 VARIO User Manual - Dutch - 32 pages

Huvema HU 550 VARIO User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info