627068

Huvema HU 460 X 1500 VAC Manual

17
Zoom out
Zoom in
Previous page
1/60
Next page
17
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
CHANG E S AND T YPI N G ERRORS RESERVED
8.11 foUr posiTion aUTo feed sTop operaTion
If it requires processing the object to a certain length or object with steps, you may use this utility to complete a
multi-section cutting.
• Place Eccentric Centering ring (12) to any require position, the highest point indicates outward. Then fix it. Now
you can try to operate Auto Feed of Apron to make sure precisely position by adjusting Eccentric Centering Ring.
• Secondly, turn Auto Centering Lever to second point. Fix second Eccentric Centering Ring as per above method.
• Same way to fix the third, the fourth.
• While Apron is auto feeding forward, only the one Eccentric Centering Ring which with its highest point outward
can touch the Auto Stop Centering (15) and stops Apron Feed, it will pass through all the rest of Eccentric
Centering Rings and will not activate at all.
8.12 TailsTock operaTion
• Tailstock Hand-wheel Dial is divided 0.02mm per graduation. Tailstock hand-wheel (28) revolves one cycle
clockwise, the quill of Tailstock feeds 5mm. If revolves anti-clockwise, the quill runs backward; when it runs to
the last the center will be automatically telecasted.
• By pushing the Tailstock Locking Lever (30) forward, you can steady the quill of Tailstock. If you wish to steady
the Tailstock or the lathe bed you only need to push Tailstock Clamping Lever forward.
8.12.1 TailsTock cenTerinG
Let loose of the Adjustment Screw (26) of Tailstock, then adjust the
other side, tighten screws on both sides after adjustment.
9. cUTTinG Threads
9.1 lead screW diVe
Forward Reverse shifting Lever (4) to right side. Lead screw (24) reversely to left side. Lead screw obverse to “N”
position, thus, lead screw will not be rotated.
9.2 cUTTinG Thread
As soon as you decide to process which threads, Please position Thread Feed Select Lever (5) Thread Feed Change
Lever (6) and 10 steps Feed Change Disc (7) in reference to the Thread Table.
Turn on the power, drive Lead screw directly.
Push down Half Nut Engaged Lever (18) and start screw cutting.
9.3 Thread dial indicaTor
To use Inch Lead screw in processing Imperial Threads.
To precede screw cutting in Imperial Threads, firstly you have to loosen
Half Nut then to match Half Nut as per instruction of Thread Dial
indicator with no necessary to change Lead screw. When you do this
procedure of threading, lock the index disc on shaft (1) than take 16T
worm gear so that you can process all Imperial threads; that is, you have
to follow the indicating plate and not to loosen Half Nut while cutting
Metric threads.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 460 X 1500 VAC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 460 X 1500 VAC in the language / languages: English as an attachment in your email.

The manual is 4,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info