627060
43
Zoom out
Zoom in
Previous page
1/48
Next page
43
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
14
8.2 Tool offset
Use this function to enter tool offsets for different tools. The operator can now use different tools,
without having to change the absolute zero or reference point. By using this function, the movement
stays consistent when changing the tools.
1. The display should be in absolute mode
(ALE) to enter tool offsets.The rst tool (1)
entered in this mode, is the reference tool.
2. Place the next tool (2) in regard to the
reference tool. The relative position of the
second tool will be:
X-axis: 25 – 30 = -5
Y-axis: 20 – 10 = 10
3. Assign a number to the tool and store this
into the readouts memory.
4. Repeat steps 2 and 3 for every other tool.
5. Data of max. 200 tools can be stored.
6. Disable this function by pressing 10
times. The function can be enabled the same
way.
The total of tools can be opened or closed. This happens in absolute mode. Press 10 times.
The tool store room is closed.
The tool store room is opened.
Entering and calling tools
The digital readout should be in abolute mode (ALE). Zero
the displayed values.
Enter the rst tool as reference point.
Enter the rst tool.
Enter the tool data for each axis.
Conrm.
Enter the next tool.
Enter the tool data for each axis.
Conrm.
Enter the next tool.
Close.
After all tool data has been entered, the total of tools can be called.
Digital readout in user mode.
Dene the reference tool. This can be the rst tool, but
also another number.
Call the second tool.
Close.
Attention!
In absolute mode, the display can only be put on 0 if the reference tool is the base
tool. In incremental mode, the display can only be put on 0 when using other tools.
Base Tool
Tool
2
Tool 1
(a)
10
30
25
20
Tool 1
Tool 2
Tool 2
10
5
±
±
Y
X
Y
X
Y
X
TOOL
5
±
TOOL
SEL
SEL
SEL
Y
X
ALE
ALE
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 1010 B-4 SINO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info