627060
44
Zoom out
Zoom in
Previous page
1/48
Next page
44
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
15
8.3 Taper calculations
The taper of the workpiece can be calculated by turning the tapered
workpiece. The sensor of the lever meter touches the workpiece at
location A. Press it to zero the lever meter.
Select the taper function.
Move the lever meter to position B on the workpiece
surface. Press it to zero the level meter.
Calculate.
The displayed value on the X-axis is the taper, the one
displayed on the Y-axis is the angle.
Close.
9. Service and maintenance
Disconnect from the mains!
Switch off the machine, disconnect from the power source and make sure that all
parts have come to a standstill before perfoming any service or maintenance.
Disconnect the digital readout from the power source before cleaning. It is recommended that the 
readout be cleaned with a lint-free cloth with a non corrosive, non abrasive cleaning uid. Make
sure that the uid can not reach or enter the connections.
Never use compressed air to clean the readout!
10. Troubleshooting
problem Possible cause Possible solution
1. Nothing happens
when the unit is
switched on
a. Unit not correctly
connected to the power
source
a. Connect the digital readout to the power source
b. Cable damaged or
defect
b. Check the power cable, replace if necessary
c. Wrong voltage c. Check that voltage of power source and digital
readout match
d. Shortcircuit in encoder d. Disconnect the encoder
2. Electrical shock
when touching the
house of the readout
a. Readout not grounded a. Ground the readout
b. Power drains off b. Check the feed
3. No data on axis a. No data a. Change both encoders. When data appears,
replace the encoder. If no data appears, replace
the digital readout
b. Special funtion chosen b. Leave the special function
4. Encoder does not
count
a. Encoder too short a. Replace with a longer encoder or shorten the
distance to be measured
b. Reader head defect b. Replace
c. Chips and dirt between
encoder and reader head
c. Remove chips and dirt
d. Distance too large
between encoder and
reader head
d. Shorten the distance
e. Cables of encoder bend
or damaged
e. Replace
f. Encoder broken f. Replace
60
°
AB
AB
0
90
80
70
60
50
40
30
20
10
30
20
70
50
40
60
10
90
80
0
8.5
4.907
A
B
Y
X
ALE
ALE
Y
X
ALE
ALE
Y
X
ALE
ALE
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Huvema HU 1010 B-4 SINO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Huvema HU 1010 B-4 SINO in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info