Manual Husqvarna Z560X (page 26 of 280) (English, German, Dutch, French, Italian, Spanish)

733969

Zoom out

Zoom in

1/280

Caster Wheels

Check every 200 hours. Check that wheels rotate

freely.

To replace, remove nut and caster bolt. Pull the

wheel out of the fork. Install in reverse order.

Tighten caster bolt. Torque to 50 ft-lbs (67.8 Nm).

NOTE: Tire must rotate freely but axle spacers

must not. If wheels do not rotate freely take the

unit to the dealer for service.

Cleaning

CAUTION! Always wear eye

protection when cleaning and

washing.

Regular cleaning and washing, especially under

the mower deck, will increase the machine’s life-

span. Make it a habit to clean the machine directly

after use (after it is cooled), before the dirt sticks.

Do not spray water on the top of the mower deck.

Use compressed air to clean the top side of

mower deck. Regularly clean deck and underside

of the deck with normal water pressure. Do not

use a high pressure washer or steam cleaner.

Avoid spraying engine and electrical components

with water.

Do not rinse hot surfaces with cold water. Let unit

cool before washing.

Hardware

Check daily. Inspect the entire machine for loose

or missing hardware.

Anti-scalp Rollers

Anti-scalp rollers keep the deck in the proper

position to help prevent scalping in most terrain

conditions. Do not adjust the rollers to support the

deck.

IMPORTANT INFORMATION Adjust anti-

scalp rollers with the mower on a at level

surface. To avoid deck damage, the anti-scalp

rollers must not be adjusted to support the

deck.

Anti-scalp rollers can be set in three positions.

• Upper 38 mm - 64 mm grass

• Middle 64 mm -102 mm grass

• Lower 102 mm - 127 mm grass

The rollers must be approximately 6.35 mm from

ground. Do not adjust the rollers to support the

deck.

Safety System

The machine is equipped with a safety system

that prevents starting or driving under the

following conditions.

The engine can only be started when:

• the mower deck is disengaged.

• the steering / park brake controls are in the

outer, locked neutral position, making sure

of full parking brake engagement for a safe

startup.

NOTE: If the steering / park brake controls are not

holding in the full outboard position, the tension

can be adjusted. (See Park Brake in this section).

Make daily inspections to make sure that the

safety system works by trying to start the engine

when one of the conditions is not met. Change

the conditions and try again.

Make sure the engine stops when the park brake

is not engaged and the operator leaves the

seated position.

Make sure the engine stops if the mower blades

are engaged and the driver leaves the seated

position.

IMPORTANT INFORMATION To drive, the

driver must sit in the seat and the steering /

park brake controls must be moved into the

engaged (outer) position. Otherwise the engine

will stop.

MAINTENANCE

What type fluids go in the two containers near the fuel tanks? Submitted on 4-6-2022 at 21:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Z560X in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 49,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna Z560X Manual

Product: