Manual Husqvarna Z560X (page 24 of 280) (English, German, Dutch, French, Italian, Spanish)

733969

Zoom out

Zoom in

1/280

Adjusting the Mower Deck

Leveling Deck

Adjust the deck while the mower is on a level

surface. Make sure the tires are inated to the

correct pressure. See Tire Pressures in this

section. If tires are under or over inated, the

deck cannot be properly adjusted. Faulty mower

deck adjustments will cause an uneven mowing

result.

Four bolts control the height and pitch of the

mower deck. Adjust the deck slightly higher in the

rear.

NOTE: To insure precision in the leveling

procedure, mower deck drive belt must be

installed prior to leveling the deck.

1. Wear heavy gloves. Turn each outer blade tip

to align with the deck side-to-side.

2. Measure from the oor surface up to the

bottom of the blade tip on the discharge

side of the mower deck. Record this

measurement. Move to the opposite side;

check that measurement is the same. If

adjustment is required, loosen the locknut

and adjust the bolt up until the two side

to side measurements are equal. Retain

measurement.

3. Turn the two outer blades to align with

the deck front to rear. Reposition the rear

mounting bolts up or down until the rear blade

tips are positioned 3.175 mm - 9.525 mm

higher in the rear than the front blade tips.

4. Conrm measurements once again. The

blade tip height must be equal side to side. In

the rear, the blade tips must be 3.175 mm -

9.525 mm higher than the front measurement.

In the front, blade tips must be equal from

side to side.

NOTE: This will place the mower deck in a

standard measurement position. Depending on

the type of grass being mowed or environmental

conditions, more adjustments may be required to

get the desired cut.

Pump Belt

The belts are not adjustable and need to be

replaced if they begin to slip from wear. Park the

mower on a level surface. Engage the park brake.

1. Remove the deck belt.

2. Remove clutch stop to access the belt.

3. Disconnect clutch wire.

4. With a 1/2" breaker bar and using the square

opening in the idler arm, shift the arm to

create slack in the belt.

5. Remove belt from the engine and pump

pulleys.

Reinstallation

1. Wrap the belt around the engine pulley and

then around the left pump pulley.

2. Route the belt around the inside of the idler

pulley.

3. With a 1/2" breaker bar and using the square

opening in the idler arm, shift the arm to

create slack in the belt.

4. While holding the idler back with the breaker

bar, wrap the belt around the right pump

pulley.

5. Replace and secure clutch stop. Reinstall the

deck belt.

6. Check the belt tension. To tighten the

belt, turn the nut on the idler eyebolt. The

recommended belt tension is 27 lb.

MAINTENANCE

What type fluids go in the two containers near the fuel tanks? Submitted on 4-6-2022 at 21:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Z560X in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 49,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna Z560X Manual

Product: