Manual Husqvarna Z560X (page 23 of 280) (English, German, Dutch, French, Italian, Spanish)

733969

Zoom out

Zoom in

1/280

V-belts

Check every 100 hours of operation. Check for

severe cracking and large nicks.

NOTE: The belt will show some small cracks in

normal operation.

Deck Belt

Deck Belt Removal

Park the mower on a level surface and engage

the park brake. Lower the deck into the lowest

cutting position.

1. Remove foot plate and belt shields.

2. Remove dirt or grass that may have

accumulated around the cutter housings and

entire deck surface.

3. Remove the belt guide hardware with a 1/2"

wrench and set the belt guide aside.

4. With a 1/2" breaker bar and using the square

opening in the idler arm, shift the arm counter

clockwise to relieve the tension on the belt.

5. Carefully lift the belt over the top of the cutter

housing pulleys.

6. Remove the belt from around the electric

clutch on the engine shaft.

Deck Belt Installation

NOTE: For ease in installing the deck belt, refer to

the routing decal on the cutting deck.

1. Place the belt around all the pulleys except

the center spindle pulley.

2. With a 1/2" breaker bar, shift the idler arm

counter clockwise. When there is enough

slack, slip the belt onto the center spindle

pulley.

3. Reinstall the belt guide removed in Step 3

above.

4. Check belt routing to make sure it matches

the routing decal and that the belt does not

have twists.

5. Adjust belt tension by turning the eyebolt nut

until there is approximately 7/8" -1" (22.2 mm -

25.4 mm) of threads showing outside the nut.

6. Belt tension must be set to 60-70 lbs.

7. Replace belt shields on the two mandrel

housings and secure with fasteners.

Cleaning Transaxle Pump and Fans

Dirt or grass accumulating around the transaxle

pump and fans can damage the fans or cause

excessive heat.

1. Push down on the latch lever to release the

seat.

2. Lift and rotate the seat fully forward until

supported by the seat rod.

3. Lift the tab on the fan guard.

4. Blow o debris accumulated around the

transaxle pump and fans.

5. Reinstall fan guard.

6. Supporting the seat, lift seat rod and lower

seat.

Blade Replacement

1. Remove blade bolt by turning it counter

clockwise.

2. Install new or resharpened blade with

stamped GRASS SIDE facing towards

ground/grass (down) or THIS SIDE UP facing

deck and cutter housing.

3. Install and tighten blade bolt securely.

4. Torque blade bolt to 90 ft-lbs (122 Nm).

IMPORTANT INFORMATION Special blade

bolt is heat treated. Replace with a Husqvarna

bolt if required. Do not use lower grade

hardware than specied.

MAINTENANCE

What type fluids go in the two containers near the fuel tanks? Submitted on 4-6-2022 at 21:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Z560X in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 49,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna Z560X Manual

Product: