734150
14
Zoom out
Zoom in
Previous page
1/368
Next page
Maintenance
Introduction
WARNING: Before you do maintenance, you
must read and understand the safety
chapter.
For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not a
service agent, speak to them for information about the
nearest service agent.
Regular service and inspection
Regular service and inspection of the product must
be done by qualified personnel referring to related
legislation and regulations.
Electrical tests for ground continuity, insulation
resistance, and condition of the flexible cord must be
done frequently.
If a defect is found, the product must be removed
from service and repaired by an approved service
technician.
Maintenance of Dust Class L products
The following applies for Dust Class L products, WDC
325L.
During maintenance and cleaning, use the product
safely for maintenance personnel or other persons.
In the maintenance area:
Use filtered mandatory airflow.
Use protective clothing.
Clean the maintenance area so that no harmful
material get out in other areas.
If the parts can not be cleaned satisfactorily during
maintenance and repair:
Put the parts in correctly sealed bags.
Discard the parts referring to legal regulations.
To empty the dirt container after liquid
pick up
1. Stop the product, see
To stop the product on page
13
.
2. Disconnect the hose from the vacuum inlet by pulling
out the hose.
3. Unlock the clasps and lift off the motor unit. (Fig. 8)
4. Empty the dirt container by tilting it rearward and put
the liquids into a floor drain. * Handle only on some
models. (Fig. 29)
CAUTION:
Always empty and clean the
dirt container and the float system after
liquid pick up. Do not pick up liquid
without the float system and filter
installed in the product.
5. Put the motor unit on the dirt container and lock the
clasps. (Fig. 12)
To empty the dirt container after dry
pick up
1. Stop the product, see
To stop the product on page
13
.
2. Unlock the clasps and lift off the motor unit. (Fig. 8)
3. Do a check to see if the filter bag is full.
4. Remove the filter bag if it is full.
CAUTION: Do not pick up dry material
without the filter and the filter bag in
position.
5. Install a new filter bag, see
To install the filter bag on
page 12
.
Note: The suction efficiency of the product depends
on the dimension and quality of the filter and the filter
bag. Use only Husqvarna filter and filter bags.
6. Put the motor unit on the dirt container and lock the
clasps. (Fig. 12)
To clean the filter, filter cleaning system
The product has a semi-automatic filter cleaning system.
Use the filter cleaning system regularly, at the latest
when the cleaning performance is no longer sufficient.
Regular use of the filter cleaning system increases the
life of the filter.
1. Clean the filter when the suction power is no longer
sufficient. (Fig. 30)
2. Put the hose in the vacuum inlet on the front of the
product. (Fig. 16)
3. Connect the appliance into the mains.
4. Put the main switch to the "I" position. (Fig. 17)
5. Put the handle in your hand (A) to make suction into
your hand.
6. Beat the filter cleaning button 3 times with your fist
(B). (Fig. 31)
7. If the suction power is not sufficient, remove the
filter, see
To replace the filter on page 15
.
8. Shake, brush or wash the filter to clean it.
9. Let the filter dry.
10. Install the filter, see
To install the filter bag on page
12
.
14
562 - 004 - 20.03.2019
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna WDC 225 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna WDC 225 in the language / languages: All languages as an attachment in your email.

The manual is 8,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info