734468

Husqvarna ST 427T Manual

15
Zoom out
Zoom in
Previous page
1/200
Next page
a) On flat surfaces set the distance between the
scraper bar and the ground to 5-6 mm (0.2-0.25
in).
b) On rough surfaces set the skid plates (A) in a
position where the scraper bar is above the top
of the ground.
WARNING: Make sure that gravel
and stones do not go into the
product. Objects that eject at high
speed can cause injury.
3. Tighten the locknut (B).
B
A
To use the drift cutters (if equipped)
Use the drift cutters to cut through snowdrifts deeper
than the front of the product.
1. Loosen the adjustment nuts (A) on both sides of the
product to allow each drift cutter (B) to be raised to
its highest position.
A
B
2. Tighten the nuts.
3. Lower the drift cutters after use.
To adjust the height of the auger
bucket (for ST 424T/427T/430T only)
1. Push the lever (A) down.
B
A
2. Move the handles (B) up or down to adjust the height
of the auger bucket .
3. Release the lever (A) to lock the auger bucket in
position.
Note: The auger bucket can be set to an unlocked
position. This lets the auger bucket adapt to the terrain.
To set the auger bucket to the unlocked position, push
the lever (A) down and to the right.
To prevent freeze-up after use
Note: Controls and moving parts can be blocked by ice.
Do not apply much force to the controls. If you cannot
operate a control or a part, start the engine and let it
operate for some minutes.
1. Start the engine and let it operate for some minutes.
Stop the engine and wait for all moving parts to stop.
2. Remove snow and loose ice from the product.
3. Remove snow and loose ice from the base of the
discharge chute.
4. Turn the discharge chute deflector to the left
direction and to the right direction to remove ice and
water.
5. Set the key to the "OFF" position.
6. If the product does not have an electric starter, pull
the starter rope handle several times to remove ice
and water.
To get a good result
• Always run the engine at full throttle or near full
throttle.
891 - 005 - 08.01.2020 15
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 427T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 427T in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info