734467

Husqvarna ST 424T, Manual

23
Zoom out
Zoom in
Previous page
1/200
Next page
To remove the auger belt (for ST 424T/427T/
430T only)
1. Remove the 5/16'' nut and the cable cover (E) from
the frame.
A
F
E
B
D
C
2. Remove the top 5/16'' bolts from the 2 sides of the
frame. Do not discard the bolts.
3. Remove the lower 5/16'' bolts (C) on the 2 sides of
the frame.
4. Remove the auger belt (B) from the engine pulley
(A).
5. Use the adjustment lever for the auger bucket to tilt
the rear section down. The front section tilts forward
at the same time. The bottom bolt is a hinge
between the front and rear sections.
6. Put a wooden block below the hinge point to set the
product in the tilted position.
7. Move the auger brake arm and remove the auger
belt (B) from around the auger brake arm.
To install the auger belt
1. Move the auger brake arm (G). Put the auger belt
around and in the groove of the auger pulley (E).
E
A
G
F
B
D
C
CAUTION: Make sure that the belt is not
caught between the frame and auger
housing as you put the unit together.
2. Remove the wooden block from below the product.
3. Lift the handles to tilt the rear section up. The front
section tilts back and pivots to attach to the rear
section.
4. Make sure that the belt is put in the auger pulley (E)
groove correctly.
5. Install the 5/16'' bolts (C), and tighten (11-16 Nm).
6. For ST 424/427/430 only: Install the ¼'' bolts (D) and
tighten (5-8 Nm).
7. Install the auger belt (B) on the engine pulley (A).
Make sure that the belt is put correctly around the
idler pulley and installed correctly in the engine
pulley groove.
8. Install the cable cover (F) and the 5/16" nut on the
frame.
9. Operate all controls to make sure that the auger belt
is installed correctly and that all components are
moving correctly.
To adjust the auger belt tension
Note: An assistant is necessary to do this task.
1. Remove the belt cover. See
To prepare for
replacement of the belts on page 21
.
891 - 005 - 08.01.2020 23
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna ST 424T, at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna ST 424T, in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info